Product Overview
Simplify your on-site communications setup with the Studio Technologies Dante audio over Ethernet capable Model 5304 Intercom Station. The 5304 features four independent talk and listen channels and a host of configurable parameters allowing it to fit seamlessly into a wide range of applications.
From on-air broadcasting to corporate AV, the 5304 provides easy configuration and control via the STcontroller software app, and it's all handled over a standard Ethernet connection. The unit also draws power from that same connection, which means only a single cable run is required for bi-directional Dante audio, power, configuration, and control.
The unit can be configured as a call center for a virtual "party-line" intercom system with other compatible devices. Five rotary controls and push buttons on the front panel facilitate level control and signal/call routing respectively. The rotary controls can also display a multi-color level meter for the input signal and the channel status.
The Model-5304 boasts a high headroom, low noise input preamp that ensures a wide dynamic range, so you hear only what you want and nothing you don't. An integrated compressor circuit helps keep levels consistent to avoid signal overload.
Studio Technologies MODEL-5304 Applications:
- On-air broadcasting
- Live event communication
- Theater
- Industrial
- Aerospace
- House of worship
- Corporate AV
Studio Technologies MODEL-5304 Features:
- Dante audio-over-Ethernet technology
- Four independent talk and listen channels
- Supports dynamic and electret microphones
- 5-pin female XLR headset connector
- Uses STcontroller for configuration
- Two remote control inputs
- Call send and receive functions
- Excellent audio quality
- AES67 and Dante Domain Manager support
- Power-over-Ethernet (PoE) powered
Studio Technologies MODEL-5304 Specifications:
- Power Source: Power-over-Ethernet (PoE): class 2 (low power, ≤6.49 watts) per IEEE® 802.3af
- Network Audio Technology:
- Type: Dante audio-over-Ethernet
- AES67-2018 Support: yes, selectable on/off
- Dante Domain Manager (DDM) Support: yes
- Bit Depth: up to 24
- Sample Rate: 48 kHz
- Pull-Up/Down Support: no
- Dante Transmitter (Output) Channels: 4
- Dante Receiver (Input) Channels: 4
- Dante Audio Flows: 4; 2 transmitter, 2 receiver
- Transmitter (Output) and Receiver (Input) Nominal Level: –20 dBFS
- Audio Channels: 4 talk, 4 listen
- Network Interface:
- Type: 100BASE-TX, Fast Ethernet per IEEE 802.3u (10BASE-T and 1000BASE-T (GigE) not supported)
- Power-over-Ethernet (PoE): Per IEEE 802.3af
- Data Rate: 100 Mb/s (10 Mb/s and 1000 Mb/s not supported)
- Microphone Input:
- Compatibility: analog dynamic or electret microphones
- Type: unbalanced
- Electret Microphone Power: 3.3 volts DC via 2 k (2000) ohms series resistance, selectable on/off
- Gain: 24, 30, 36, 42, or 48 dB, selectable
- Frequency Response: 42 Hz to 18 kHz, –3 dB, nominal
- Distortion (THD+N):
- Noise Floor: –94 dBFS (A-weighted)
- Compressor:
- Threshold: 1.5 dB above nominal level (–18.5 dBFS)
- Slope: 2:1
- Headphone Output:
- Type: 2-channel
- Compatibility: intended for connection to stereo (dual-channel) or monaural (single-channel) headsets with nominal impedance of 50 ohms or greater
- Maximum Output Voltage: 2.9 Vrms, 1 kHz, with 150 ohm load
- Frequency Response: 7 Hz to 9.8 kHz, –3 dB
- Distortion (THD+N):
- Dynamic Range: >100 dB
- Call Send Function:
- Signaling Method: 20 kHz, within selected Dante transmitter (output) audio channels
- Send Level: –20 dBFS
- Call Receive Function:
- Sources: Dante receiver (input) channels 1-4
- Signaling Method: 20 kHz +/-800 Hz, nominal, within audio channels
- Receive Level: –27 dBFS minimum
- Detect Time: 10 milliseconds, minimum
- Remote Control Inputs: 2
- Function: configurable, can mimic the action of any of the five button functions
- Type: active low, 1 mA maximum, inputs pulled up to 3.3 volts DC via 3.4 k (3400) ohm resistors
- Connectors:
- Headset: 5-pin female XLR
- Ethernet: RJ45 jack
- Remote Control Inputs: 3-conductor (TRS) 3.5 mm jack
- USB: type A receptacle (used only for updating application firmware)
- Configuration: requires Studio Technologies' STcontroller software application
- Software Updating: USB flash drive used for updating application firmware; Dante Updater application for updating Dante interface firmware
- Environmental:
- Operating Temperature: 0 to 50 degrees C (32 to 122 degrees F)
- Storage Temperature: –40 to 70 degrees C (–40 to 158 degrees F)
- Humidity: 0 to 95%, non-condensing
- Altitude: not characterized
- Dimensions (Overall):
- 8.70 inches wide (22.1 cm)
- 1.72 inches high (4.4 cm)
- 4.45 inches deep (11.3 cm)
- Weight: 0.95 pounds (0.42 kg); rack-mounting installation kits add approximately 0.2 pounds (0.09 kg)
- Deployment: intended for tabletop applications. Four optional mounting kits are also available:
- RMBK-10 allows one unit to be mounted in a panel cutout or on a flat surface
- RMBK-11 allows one unit to be mounted in the left- or right-side of one space (1U) of a standard 19-inch rack
- RMBK-12 allows two units to be mounted in one space (1U) of a standard 19-inch rack
- RMBK-13 allows one unit to be mounted in the center of one space (1U) of a standard 19-inch rack