Product Overview
Crestron offers the HD-RX-4K-510-C-E 4K Multiformat 5x1 AV Switch and Receiver, compatible with all DM Lite™ transmitters.
This unit features three DM Lite inputs, two HDMI® inputs and one scaling HDMI output. It also includes amplified audio outputs for speakers, five analog audio inputs and two analog audio outputs. Also includes IR, RS-232, relay, I/O and Ethernet control ports. Also supports .AV Framework technology.
The Crestron® HD RX 4K 510 C E multiformat AV switch and receiver provides enhanced HDMI® video switching and audio presentation capabilities in areas such as conference rooms and classrooms. Compatible with all DM Lite™ transmitters, the HD RX 4K 510 C E provides three DM Lite inputs for connection to up to three transmitters. A CATx (CAT5e or higher) twisted pair cable connects a transmitter to the HD RX 4K 510 C E for the transmission of HDMI signals. For resolutions up to 2K, the maximum transmission distance is 230 ft (70 m). For higher resolutions up to 4K, the maximum transmission distance is 130 ft (40 m).1
NOTE: Power is transmitted over the CATx cable that connects the HD RX 4K 510 C E to a DM Lite transmitter. The HD RX 4K 510 C E can power three transmitters simultaneously.
In addition to three DM Lite inputs, the HD RX 4K 510 C E provides two HDMI inputs that can be connected to local AV sources.
Specifications
- Switcher: 5x1 auto-switching or manual, audio-follows-video, Crestron Auto-Locking® and QuickSwitch HD™ technologies
- Scaler (HDMI Output): 4K video scaler with motion-adaptive deinterlacing, intelligent frame rate conversion, Deep Color support, content-adaptive noise reduction, 3:2/2:2 pull-down detection and recovery
- Input Signal Types: HDMI with Deep Color and 4K (DVI and Dual-Mode DisplayPort™ interface compatible3) on Inputs 1-2, DM Lite with Deep Color and 4K on Inputs 3-5
- Output Signal Types: HDMI with Deep Color and 4K (DVI compatible4)
- Copy Protection HDCP 2.2
- Switcher/Mixer: 6x2 audio mixer
- Audio Inputs:
- Two stereo 2-channel LINE inputs
- Two mono 1-channel MIC inputs
- One mono 1-channel AUX input
- One stereo 2-channel LPCM audio extracted from the selected HDMI or DM Lite input source
- Audio Outputs:
- One mirrored AUX 1, SPEAKER, and HDMI mixer output, stereo 2-channel
- One AUX 2 output, stereo 2-channel
- Analog-to-Digital Conversion: 24-bit 48 kHz
- Digital-to-Analog Conversion: 24-bit 48 kHz
- Frequency Response, Analog Audio Outputs:
- 20 Hz to 20 kHz ±0.5 dB (AUX outputs)
- 20 Hz to 20 kHz @ full power ±3 dB (speaker output)
- S/N Ratio, Analog Audio Outputs:
- >95 dB @ 10 dBV, 20 Hz to 20 kHz, A-weighted (AUX outputs)
- >90 dB @ 10 dBV, 20 Hz to 20 kHz, A-weighted (speaker output)
- THD+N, Analog Audio Outputs:
- Stereo Separation, Analog Audio Outputs:
- 20 Hz to 20 kHz ≤80 dB (AUX outputs)
- 20 Hz to 20 kHz ≤60 dB (speaker output)
- Audio, Microphone Inputs: Two balanced 1-channel microphone inputs (MIC 1 and MIC 2)
- Input Signal Type: Mono analog
- Phantom Power: +48 VDC, 12 mA, enable or disable per channel
- Gain: 0 dB to +60 dB per channel in 1 dB increments
- Mute: Enable or disable per channel
- Audio, Line Inputs: Two balanced/unbalanced 2-channel line inputs (LINE 1 and LINE 2)
- Input Signal Type: Stereo analog
- Balanced Line Input Level: 4 Vrms
- Unbalanced Line Input Level: 2 Vrms
- Line Input Impedance: >10k ohms
- Audio, Auxiliary Input
- One balanced 1-channel auxiliary input (AUX):
- Input Signal Type: Mono analog
- Balanced Line Input Level: 4 Vrms
- Line Input Impedance: >10k ohms
- Audio, Source Inputs
- Two HDMI and three DM Lite inputs (HDMI 1-2 and DM Lite 3- 5):
- Input Signal Types: HDMI (Dual-Mode DisplayPort interface compatible), DM Lite
- Digital Formats 2-channel LPCM
- One mirrored SPEAKER, HDMI, and balanced/unbalanced AUX 1 mixer output:
- Output Signal Type/Format: Stereo 2-channel
- AUX 1 Output Impedance: 200 ohms balanced, 100 ohms unbalanced
- AUX 1 Maximum Output Level: 4 Vrms balanced, 2 Vrms unbalanced
- Selected Source: -80 dB to +20 dB level adjustment range plus Mute
- MIC 1-2: -80 dB to +20 dB level adjustment range plus Mute
- LINE 1-2: -80 dB to +20 dB level adjustment range plus Mute
- AUX: -80 dB to +20 dB level adjustment range plus Mute
- Master Volume: -80 dB to +20 dB level adjustment range plus Mono
- Amplifier Output Power: 25 W RMS per channel @ 8 ohms, 4 ohms tolerant
- Amplifier Power: On or off
- Mute: Enable or disable independently for AUX 1, SPEAKER, and HDMI mixer output
- One balanced/unbalanced AUX 2 output:
- Output Signal Type/Format: Stereo 2-channel
- Output Impedance: 200 ohms balanced, 100 ohms unbalanced
- Maximum Output Level: 4 Vrms balanced, 2 Vrms unbalanced
- Selected Source: -80 dB to +20 dB level adjustment range plus Mute
- MIC 1-2: -80 dB to +20 dB level adjustment range plus Mute
- LINE 1-2: -80 dB to +20 dB level adjustment range plus Mute
- AUX: -80 dB to +20 dB level adjustment range plus Mute
- Master Volume: -80 dB to +20 dB level adjustment range plus Mono
- Mute: Enable or disable for AUX 2
- Ethernet: 100/1000 Mbps, auto-switching, auto-negotiating, auto-discovery, full/half duplex, CIP, DHCP, web browser setup and control
- RS-232: 2-way device control and monitoring up to 115.2k baud with hardware and software handshaking
- IR: 1-way device control via infrared up to 60 kHz
- HDMI: HDCP 2.2, EDID, CEC
- DM Lite: HDCP 2.2, EDID
- L/R, LINE INPUT 1-2: (2) 5-pin 3.5 mm detachable terminal blocks
- MIC INPUT 1-2: (2) 3-pin 3.5 mm detachable terminal blocks
- AUX INPUT: (1) 3-pin 3.5 mm detachable terminal block
- HDMI INPUT 1 – 2: (2) HDMI Type A connectors, female; HDMI digital video/audio inputs; DVI and Dual-Mode DisplayPort interface compatible
- DM Lite INPUT 3-5: (3) 8-pin RJ-45 yellow connectors, female, shielded; DM Lite input ports for connection to DM Lite transmitters
- L/R, AUX OUT 1-2: (2) 5-pin 3.5 mm detachable terminal blocks
- HDMI OUTPUT: (1) HDMI Type A connector, female; HDMI digital video/audio output;2 DVI compatible
- NOTE: CEC over the HDMI output provides Power On/Off control of the display device without a control system or full programmable control of any device with a control system.
- Ethernet: (1) 8-pin RJ-45 connector, female; 100BASE-TX/1000BASE-T Ethernet port
- SPEAKER OUTPUT: (2) 2-pin 7.62 mm reversed gender 20 A detachable terminal blocks, power amplifier outputs; Wire Size: Terminals accept up to 12 AWG (3.31 mm); Output is direct-coupled—not transformer isolated
- I/O 1-2: (2) 2-pin detachable terminal blocks; Comprises 2 Versiport digital input/output or analog input ports (referenced to GND)
- Digital Input: Rated to 0-24 VDC, input impedance 20k ohms, logic threshold >3.125 V low/0 and
- Digital Output: 250 mA sink from maximum 24 VDC, catch diodes for use with "real world" loads;
- Analog Input: Rated for 0-10 VDC, protected to 24 VDC maximum, input impedance 21k ohms with pull-up resistor disabled; Programmable 5 V, 2k ohms pull-up resistor per pin
- RLY 1-2: (2) 2-pin detachable terminal blocks; Comprise 8 normally open, isolated relays; Rated 1 A, 30 VAC/VDC; MOV arc suppression across contacts
- IR: (1) 2-pin 3.5 mm detachable terminal block; IR output control port; supports IR up to 60 kHz; IRP2 emitter sold separately
- NOTE: The IR port provides Power On/Off control of the display device with the use of a control system.
- COM: (1) 5-pin 3.5 mm detachable terminal block; Bidirectional RS-232 port; Supports RS-232 up to 115.2k baud with hardware and software handshaking
- NOTE: The COM port provides Power On/Off control of the display device without a control system or full programmable control of any device with a control system.
- 100-240V 4A-2A 50/60 Hz: (1) IEC 60320 C14 mains power inlet: Mates with removable power cord, included
- NOTE: This power connection powers both the HD-RX-4K-510-C-E and all connected DM Lite transmitters. When connected to the HD-RX-4K-510-C-E, DM Lite transmitters must not be connected to power.
- SERVICE: (1) USB Type A connector, female; For factory use only
- PWR: (1) LED, indicates that power is being applied to the HD-RX-4K-510-C-E. Amber indicates that the device is booting. Green indicates that the device is operational.
- INPUT 1-5: (5) Push buttons for manual input selection and (5) LEDs. Green indicates that video is switched. Amber indicates that video is detected but is not switched.
- AUTO: (1) Push button to enable or disable automatic switching, and (1) green LED to indicate that automatic switching is enabled
- SETUP: (1) Red LED and (1) push button for display of IP address on the HDMI output
- DM Lite: (2) LEDs on RJ-45 connector. Green indicates that a DM Lite link is established. Flashing amber indicates non-HDCP video and solid amber indicates HDCP video.
- Ethernet: (2) LEDs on RJ-45 connector. Green indicates that an Ethernet link is established. Flashing amber indicates Ethernet activity.
- Mains Power: 4 A - 2 A @ 100-240 VAC, 50/60 Hz
- NOTE: The AC mains power connection powers both the HD-RX-4K-510-C-E and all connected DM Lite transmitters. When connected to the HD-RX-4K-510-C-E, DM Lite transmitters must not be connected to power.
- Temperature: 32° to 104° F (0° to 40° C)
- Humidity: 10% to 90% RH (non-condensing)
- Chassis: Metal, black finish, vented sides, 2 mounting flanges attached
- Mounting: Surface mount
- Height: 10.22 in (260 mm)
- Width: 14.18 in (361 mm) with mounting flanges attached
- Depth: 1.74 in (45 mm)
- Weight: 7.5 lb (3.4 kg) with mounting flanges attached
