Product Overview
This fixture comes in black with a 1.5 m powerCON power-input cable with an Edison connector.
ColorSource Spot jr gives you more of what you love at a fraction of the cost and a fraction of the size. This fixture uses the same color technology as other ETC fixtures including droop compensation, extensive third-party lifetime testing and comprehensive factory color calibration. With 5,700 lumens of brightness coming out of this light-weight fixture, ColorSource Spot jr fits any need.
ColorSource Spot jr has built-in zoom capability that is great for small stages, clubs and retail spaces. Longer throws and short trim heights make this an all-purpose luminaire. Highlight a performer with a special in one show and add texture with a breakup pattern in another.
ColorSource luminaires are factory-calibrated to ensure consistency. They feature a four-color mixing system offering bright, vibrant colors and perfectly-mixed pastels. The thermal management algorithms built into every ColorSource fixture ensure that the colors you choose in rehearsal are the colors you get during the show.
ColorSource Spot jr was designed to have an L70 rating of 50,000 hours. Whether it is an IES-approved LM-84 or LM-80 plus in-situ test, independent test agencies confirm that it will stand up to the test of time.
Most LED luminaire manufacturers offer a 2-year limited warranty. ETC offers a 5-year warranty on the entire fixture, and an astonishing 10-year warranty on the LED array.
Lower watts for more output mean lower power consumption and increased luminaires per circuit. Lower wattage means more fixtures on a single circuit, so you’ll get more light where you need it.
Specifications
- All LED fixtures shall be provided by a single manufacturer to ensure compatibility
- The fixture shall be UL 1598 listed
- The fixture shall comply with the USITT DMX512-A standard
- The fixture shall be provided with the minimum warranty of 5 years full fixture coverage and 10 years LED array coverage
- The fixture shall have LM-80 testing for all LEDs with a L70 rating of no less than 54,000 hours
- The unit shall be constructed of rugged Acrylonitrile butadiene styrene (ABS) plastic
- The unit shall utilize a 7-segment display for settings and operation
- 0.024” full hard 301 stainless steel shutters
- Rugged steel yoke with two mounting positions allowing 300+ rotation of the fixture within the yoke
- Power supply, cooling and electronics shall be integral to each unit
- The light beam should have a 2-to-1 center-to-edge drop-off ratio
- Low gate and beam temperature
- Sharp imaging through a three-plane shutter design
- The unit shall provide, but not be limited to:
- Sharp shutter cuts without halation
- Shutter warping and burnout in normal use shall be unacceptable
- Adjustable hard and soft beam edges
- The unit shall have a 55mm gate, utilizing an M-sized pattern holder
- The fixture shall be ETL and cETL LISTED and/or CE rated, and shall be so labeled when delivered to the job site
- The fixture shall be ETL LISTED to the UL1598
- The fixture shall be rated for IP-20 dry location use
- Fixture shall be equipped with a cooling fan
- The fixture shall utilize advanced thermal management systems to maintain LED life to an average of 70% intensity after 54,000 hours of use
- Fixture shall be calibrated at factory to achieve consistent color and intensity output between fixtures built at different times and/or from different LED lots or bins
- Calibration data shall be stored on the control card as a permanent part of on-board operating system
- All arrays, including replacement arrays shall be calibrated to the same standard to insure consistency
- Fixtures not offering LED calibration shall not be acceptable
- The fixture shall utilize a minimum of 52 LED emitters
- These emitters shall be made up of Red, Green, Indigo and Lime for ColorSource Spot jr Deep Blue
- The LED system shall use 15-bit nonlinear scaling techniques for high-resolution dimming
- The fixture shall utilize an Incandescent dimming curve
- Dimming curve shall be optimized for smooth dimming over longer timed fades.
- The LED system shall be digitally driven using high-speed pulse width modulation (PWM)
- LED control shall be compatible with broadcast equipment in the following ways:
- PWM control of LED levels shall be imperceptible to video cameras and related equipment
- PWM shall be capable of being set via RDM to 25,000hz
- The fixture shall be USITT DMX512-A compatible via In and Thru 5-pin XLR connectors
- The fixture shall be compatible with the ANSI RDM E1.20 standard
- All fixture functions shall accessible via RDM protocol for modification from suitably equipped control console
- Temperature sensors within the luminaire shall be viewable in real time via RDM
- Fixtures not offering RDM compatibility, feature set access or temperature monitoring via RDM shall not be compatible
- The fixture shall be equipped with a 7-segment display
- The fixture shall be equipped with a three-button user-interface
- A variable-rate strobe channel shall be provided
- The fixture shall offer stand-alone functionality eliminating the need for a console
- Fixture shall ship with 12 preset colors or color temperatures accessible as a stand-alone feature
- Fixture shall ship with 5 sequences accessible as a stand-alone feature
- Each color and sequence can be modified by the end user via RDM
- Fixtures can be linked together with standard DMX cables and controlled from designated master fixture
- Up to 32 fixtures may be linked
- Fixtures in a stand-alone state shall restore to the settings present prior to power cycling, eliminating the need for reprogramming
- Fixtures without stand-alone operation features described above shall not be acceptable
