(0)

Questions? Call Us:
866-334-8859

Radio Design Labs ST-RG1
Ramp Generator

OUR PART #  STRG1

Our Price: $110.54
List Price: $147.86
You save 25%! (Low Price Guarantee)
In Stock

Recommended Accessories

Radio Design Labs' ST-RG1 is a digitally generated 0 to 10 volt Ramp Generator in the group of STICK-ON series products by Radio Design Labs. These products are designed for quick, convenient installation, and reliable operation in a variety of control applications.

The ST-RG1 provides many important features:

  • Its 0 to 10 volt output is the ideal interface toremotely control voltage Controlled Amplifiers, such as RDLs popular ST-VCA2
  • A single VCA may now be controlled from severallocations. Only a pair of buttons, (UP and DOWN), is required at each controllocation, or RDL's RLC2 Remote Level Contro2
  • LED level indicator driver circuitry is included in the ST-RG1

NOTE: Radio Design Labs' PS-24AS power supply is NOT included but is required in order to power this product.  Please see the "Accessories" tab or click here for more information on the PS-24AS power supply.

The ST-RG1 provides terminals for connection of two momentary buttons; one to ramp up, the other to ramp down. This is usually accomplished with RDLs RLC2 Remote Level Control. When power is applied to the ST-RG1, the output terminal is at its lowest (0 volt) point. When the UP button is pushed, the output ramps upward. When the UP button is released, the output remains stable at the voltage present when the button was released. When the DOWN button is depressed, the output ramps downward as long as the button is held in. When the ST-RG1 output reaches either minimum or maximum, it remains there until the opposite button (or closure) is applied. If the remote button is pushed momentarily and not held in, the ramp will step 200 millivolts, nominal, in the selected direction.

Two LED outputs are provided. A red LED connects to the LOW output; a green connects to the HIGH output. When the ramp is fully on (10 volts), the green indicator is fully on, and the red is fully off. When the ramp is at minimum, the red is fully on and the green is fully off. The circuit is designed to vary the current to each LED in proportion to the relative position of the ramp. If the ramp is at 5 volts then both indicators are equally illuminated. With this system, only two LEDs are required for full visual level indication!

The ST-RG1 provides the ideal interface for audio volume control through RDLs ST-VCA2 voltage Controlled Amplifier. The ST-RG1 is a Ground-referenced product which may operate from the same power supply as the ST-VCA2. Any number of UP and DOWN buttons may be connected to the ST-RG1, allowing VCA control from multiple locations. The output drive current from the ST-RG1 is more than sufficient to drive two ST-VCA2s.

Specifications:

  • Control Inputs (2): 1 to ramp UP, 1 to ramp DOWN
  • Input Logic: External closure pulls normally low input to +15 Vdc to activate UP or DOWN function
  • Indicator Outputs:
        * 1 to drive red LED partial tofully OFF
        * 1 to drive green LED partial to fully ON
  • LED Output Current: 0 to 3 mA (to drive low current, high intensity LEDs)
  • Ramp Output: 0 to 10 volts nominal, (typical less than 0.1 v to greater than 9.8 v under ST-VCA2 load)
  • Minimum Step: 200 mV nominal
  • Ramp Time: 5 seconds (fully off to fully on; or fully on to fully off)
  • Power Requirement: 24 to 33 Vdc @ 40 mA, Ground-Referenced
Stick-On Mounting Rack for 10 UnitsRadio Design Labs SR-10 Stick-On Mounting Rack for 10 Units

Radio Design Labs' STR-10 Racking System holds up to 10 STICK-ON units.  It holds STICK-ONs at an angle allowing for control adjustment from either the edge of a STICK-ON, or the top (depending on where the adjustment is located on ...

In Stock

Free Shipping Available

Our Price:$64.12List Price: $85.76You save 25%!

24 VDC 500mA Switching Power SupplyRadio Design Labs PS-24AS 24 VDC 500mA Switching Power Supply

Radio Design Labs' PS-24AS is a 24 Vdc switching power supply with a North American AC plug.  500 mA, dc plug.Specifications: Input: 100 to 240 VACOutput: 24 Vdc, 500 mA (UL, CSA)Dimensions: 1.65" x 2.75" x 1.45" (4.2 x 7 x 3.7 ...

In Stock

Our Price:$22.92List Price: $30.67You save 25%!

Din Rail Adaptor for STICK-ON Radio Design Labs DRA-35S Din Rail Adaptor for STICK-ON

The DRA-35S is a 35 mm DIN rail mounting bracket that provides positive mounting for any RDL STICK-ON® module. The oblique mounting angle of the DRA-35S allows an installer to mount several STICK-ON modules to a single DIN rail. Access to ...

In Stock

Our Price:$19.02List Price: $22.44You save 15%!

Kit to Mount ST, TX Series Modules on FP PanelRadio Design Labs MB3-RDL Kit to Mount ST, TX Series Modules on FP Panel

TX or STICK-ON Module fastens to MB-3 which slides into FP-RRA/H track.

In Stock

Our Price:$5.01List Price: $6.70You save 25%!

Mounting Kit for STICK-ON, TX, or Rack-Up moduleRadio Design Labs MB1-RDL Mounting Kit for STICK-ON, TX, or Rack-Up module

Two mounting brackets mounts a STICK-ON, TX, or Rack-Up module to a flat surface.

In Stock

Our Price:$3.39List Price: $4.00You save 15%!

Rackmount Kit for 10 Stick-On UnitsRadio Design Labs STR-19B Rackmount Kit for 10 Stick-On Units

Radio Design Labs' STR-19B Racking System holds up to 10 STICK-ON unitss in a 19 inch rack and only occupies two rack spaces. The STR-19B holds STICK-ONs at an angle allowing for control adjustment from either the edge of a STICK-ON, or ...

Usually ships in 7-14 business days.
Need it sooner? Call us!

Free Shipping Available

Our Price:$159.34List Price: $213.14You save 25%!

Rackmount System for 12 Stick-On UnitsRadio Design Labs STR-19A Rackmount System for 12 Stick-On Units

Radio Design Labs' STR-19A Racking System holds up to 12 STICK-ONs in a 19" rack and only occupies two rack spaces.

Usually ships in 7-14 business days.
Need it sooner? Call us!

Free Shipping Available

Our Price:$134.02List Price: $179.28You save 25%!

Single RACK-UP Mounting Bay Utility ChassisRadio Design Labs UC-1 Single RACK-UP Mounting Bay Utility Chassis

Radio Design Labs' UC-1 is an ULTRASTYLE design tabletop chassis for mounting RDL modules and accessories. The front panel features a single RACK-UP mounting bay. The rear panel has an identical mounting bay and is supplied with matching ...

Usually ships in 7-14 business days.
Need it sooner? Call us!

Our Price:$84.01List Price: $112.37You save 25%!

Mounting Frame for Stick/TXRadio Design Labs SR-4 Mounting Frame for Stick/TX

Radio Design Labs' SR-4 is a universal module chassis that can mount to a backboard, wall or nearly any other support. It provides mounting for 4 STICK-ON power amplifiers or 7 standard STICK-ON modules. TX ™ modules may also be mounted. ...

Usually ships in 7-14 business days.
Need it sooner? Call us!

Our Price:$83.21List Price: $111.30You save 25%!

STICK-ON Series 19"W Mounting Rack for up to12 ModulesRadio Design Labs SR-12A STICK-ON Series 19"W Mounting Rack for up to12 Modules

Radio Design Labs' SR-12A chassis can be mounted in a rack or on a backboard to provide mounting of 12 STICK-ONs.

Usually ships in 7-14 business days.
Need it sooner? Call us!

Our Price:$64.12List Price: $85.76You save 25%!

Mounting Strip for STICK-ON UnitsRadio Design Labs Smk 12 Mounting Strip for STICK-ON Units

The SMK-12 allows removable surface (up to 6 units) or edge (typically 12, max. 16) mounting of STICK-ON units. They can be fastened to its surface using screws or adhesive foam pads.

Usually ships in 7-14 business days.
Need it sooner? Call us!

Our Price:$27.45List Price: $36.72You save 25%!

Detachable Terminal BlockRadio Design Labs Dtb Rdl Detachable Terminal Block

Use DTB's to quickly detach and reattach wiring harness to STICK-ON units.

Usually ships in 7-14 business days.
Need it sooner? Call us!

Our Price:$6.77List Price: $8.00You save 15%!

Click to download

Radio Design Labs ST-RG1
Ramp Generator

OUR PART #  STRG1

Product Information:

Radio Design Labs' ST-RG1 is a digitally generated 0 to 10 volt Ramp Generator in the group of STICK-ON series products by Radio Design Labs. These products are designed for quick, convenient installation, and reliable operation in a variety of control applications.

The ST-RG1 provides many important features:

  • Its 0 to 10 volt output is the ideal interface toremotely control voltage Controlled Amplifiers, such as RDLs popular ST-VCA2
  • A single VCA may now be controlled from severallocations. Only a pair of buttons, (UP and DOWN), is required at each controllocation, or RDL's RLC2 Remote Level Contro2
  • LED level indicator driver circuitry is included in the ST-RG1

NOTE: Radio Design Labs' PS-24AS power supply is NOT included but is required in order to power this product.  Please see the "Accessories" tab or click here for more information on the PS-24AS power supply.

The ST-RG1 provides terminals for connection of two momentary buttons; one to ramp up, the other to ramp down. This is usually accomplished with RDLs RLC2 Remote Level Control. When power is applied to the ST-RG1, the output terminal is at its lowest (0 volt) point. When the UP button is pushed, the output ramps upward. When the UP button is released, the output remains stable at the voltage present when the button was released. When the DOWN button is depressed, the output ramps downward as long as the button is held in. When the ST-RG1 output reaches either minimum or maximum, it remains there until the opposite button (or closure) is applied. If the remote button is pushed momentarily and not held in, the ramp will step 200 millivolts, nominal, in the selected direction.

Two LED outputs are provided. A red LED connects to the LOW output; a green connects to the HIGH output. When the ramp is fully on (10 volts), the green indicator is fully on, and the red is fully off. When the ramp is at minimum, the red is fully on and the green is fully off. The circuit is designed to vary the current to each LED in proportion to the relative position of the ramp. If the ramp is at 5 volts then both indicators are equally illuminated. With this system, only two LEDs are required for full visual level indication!

The ST-RG1 provides the ideal interface for audio volume control through RDLs ST-VCA2 voltage Controlled Amplifier. The ST-RG1 is a Ground-referenced product which may operate from the same power supply as the ST-VCA2. Any number of UP and DOWN buttons may be connected to the ST-RG1, allowing VCA control from multiple locations. The output drive current from the ST-RG1 is more than sufficient to drive two ST-VCA2s.

Specifications:

  • Control Inputs (2): 1 to ramp UP, 1 to ramp DOWN
  • Input Logic: External closure pulls normally low input to +15 Vdc to activate UP or DOWN function
  • Indicator Outputs:
        * 1 to drive red LED partial tofully OFF
        * 1 to drive green LED partial to fully ON
  • LED Output Current: 0 to 3 mA (to drive low current, high intensity LEDs)
  • Ramp Output: 0 to 10 volts nominal, (typical less than 0.1 v to greater than 9.8 v under ST-VCA2 load)
  • Minimum Step: 200 mV nominal
  • Ramp Time: 5 seconds (fully off to fully on; or fully on to fully off)
  • Power Requirement: 24 to 33 Vdc @ 40 mA, Ground-Referenced
Stick-On Mounting Rack for 10 UnitsRadio Design Labs SR-10 Stick-On Mounting Rack for 10 Units

Radio Design Labs' STR-10 Racking System holds up to 10 STICK-ON units.  It holds STICK-ONs at an angle allowing for control adjustment from either the edge of a STICK-ON, or the top (depending on where the adjustment is located on ...

In Stock

Free Shipping Available

Our Price:$64.12List Price: $85.76You save 25%!

24 VDC 500mA Switching Power SupplyRadio Design Labs PS-24AS 24 VDC 500mA Switching Power Supply

Radio Design Labs' PS-24AS is a 24 Vdc switching power supply with a North American AC plug.  500 mA, dc plug.Specifications: Input: 100 to 240 VACOutput: 24 Vdc, 500 mA (UL, CSA)Dimensions: 1.65" x 2.75" x 1.45" (4.2 x 7 x 3.7 ...

In Stock

Our Price:$22.92List Price: $30.67You save 25%!

Din Rail Adaptor for STICK-ON Radio Design Labs DRA-35S Din Rail Adaptor for STICK-ON

The DRA-35S is a 35 mm DIN rail mounting bracket that provides positive mounting for any RDL STICK-ON® module. The oblique mounting angle of the DRA-35S allows an installer to mount several STICK-ON modules to a single DIN rail. Access to ...

In Stock

Our Price:$19.02List Price: $22.44You save 15%!

Kit to Mount ST, TX Series Modules on FP PanelRadio Design Labs MB3-RDL Kit to Mount ST, TX Series Modules on FP Panel

TX or STICK-ON Module fastens to MB-3 which slides into FP-RRA/H track.

In Stock

Our Price:$5.01List Price: $6.70You save 25%!

Mounting Kit for STICK-ON, TX, or Rack-Up moduleRadio Design Labs MB1-RDL Mounting Kit for STICK-ON, TX, or Rack-Up module

Two mounting brackets mounts a STICK-ON, TX, or Rack-Up module to a flat surface.

In Stock

Our Price:$3.39List Price: $4.00You save 15%!

Rackmount Kit for 10 Stick-On UnitsRadio Design Labs STR-19B Rackmount Kit for 10 Stick-On Units

Radio Design Labs' STR-19B Racking System holds up to 10 STICK-ON unitss in a 19 inch rack and only occupies two rack spaces. The STR-19B holds STICK-ONs at an angle allowing for control adjustment from either the edge of a STICK-ON, or ...

Usually ships in 7-14 business days.
Need it sooner? Call us!

Free Shipping Available

Our Price:$159.34List Price: $213.14You save 25%!

Rackmount System for 12 Stick-On UnitsRadio Design Labs STR-19A Rackmount System for 12 Stick-On Units

Radio Design Labs' STR-19A Racking System holds up to 12 STICK-ONs in a 19" rack and only occupies two rack spaces.

Usually ships in 7-14 business days.
Need it sooner? Call us!

Free Shipping Available

Our Price:$134.02List Price: $179.28You save 25%!

Single RACK-UP Mounting Bay Utility ChassisRadio Design Labs UC-1 Single RACK-UP Mounting Bay Utility Chassis

Radio Design Labs' UC-1 is an ULTRASTYLE design tabletop chassis for mounting RDL modules and accessories. The front panel features a single RACK-UP mounting bay. The rear panel has an identical mounting bay and is supplied with matching ...

Usually ships in 7-14 business days.
Need it sooner? Call us!

Our Price:$84.01List Price: $112.37You save 25%!

Mounting Frame for Stick/TXRadio Design Labs SR-4 Mounting Frame for Stick/TX

Radio Design Labs' SR-4 is a universal module chassis that can mount to a backboard, wall or nearly any other support. It provides mounting for 4 STICK-ON power amplifiers or 7 standard STICK-ON modules. TX ™ modules may also be mounted. ...

Usually ships in 7-14 business days.
Need it sooner? Call us!

Our Price:$83.21List Price: $111.30You save 25%!

STICK-ON Series 19"W Mounting Rack for up to12 ModulesRadio Design Labs SR-12A STICK-ON Series 19"W Mounting Rack for up to12 Modules

Radio Design Labs' SR-12A chassis can be mounted in a rack or on a backboard to provide mounting of 12 STICK-ONs.

Usually ships in 7-14 business days.
Need it sooner? Call us!

Our Price:$64.12List Price: $85.76You save 25%!

Mounting Strip for STICK-ON UnitsRadio Design Labs Smk 12 Mounting Strip for STICK-ON Units

The SMK-12 allows removable surface (up to 6 units) or edge (typically 12, max. 16) mounting of STICK-ON units. They can be fastened to its surface using screws or adhesive foam pads.

Usually ships in 7-14 business days.
Need it sooner? Call us!

Our Price:$27.45List Price: $36.72You save 25%!

Detachable Terminal BlockRadio Design Labs Dtb Rdl Detachable Terminal Block

Use DTB's to quickly detach and reattach wiring harness to STICK-ON units.

Usually ships in 7-14 business days.
Need it sooner? Call us!

Our Price:$6.77List Price: $8.00You save 15%!

Click to download

Add to Cart

We're sorry, only of this item available



Call a Sales Pro at 800-356-5844 for more information

© 2016 Full Compass Systems, LTD  9770 Silicon Prairie Parkway, Madison, WI 53593  All rights reserved.

We are not responsible for typographical errors in pricing or product specification
inaccuracies in our catalog or web site. Prices are subject to change without notice.