Product Overview
Thanks to LD Systems' IPA412T can have a permanently installed audio system with the flexibility you need today and adaptability you'll appreciate tomorrow. The 120-watt Class-D amplifier supports operation at low impedance (4Ω) and on 70/100V distributed lines for maximum flexibility in original and retrofit installations. Integrated DSP functions, such as a parametric EQ with matching speaker library and dynamic tools, provide users with unparalleled control over their soundscape. Ease of use is at the core of the IPA series design. A user-friendly front panel displays at-a-glance LED verification of signal, limit, protection, mute, and bridge mode status for each channel as well as clipping on the inputs. The unit's internal DSP also features a parametric EQ and DIP switch selectable preset high-pass/low-pass configurations. Looking to the future, you'll see the IPA412T is equipped for integration with LD Systems' upcoming remote control panels and paging microphones (sold separately). You'll find priority source selection and delay as available options allowing you to adapt to variances in room size and attendance numbers as well as safety and security requirements. Plus there's an expansion slot just waiting for optional Ethernet, or Ethernet + Dante cards (sold separately). With scalability and future-proof design, the IPA412T offers the quality and peace of mind installers and end users demand.
LD Systems IPA412T Applications:
- Hospitality
- Corporate enterprise
- Academic institutions
- House of worship
LD Systems IPA412T Features:
- Professional 4-channel installation amplifier
- Powerful class-D power amplifier with 4 x 120 W (IPA 412 T) or 4 x 240 W (IPA 424 T) at 4 Ohm (transformer bypass) or 70V/100V outputs through toroidal core transformer
- Stereo/parallel/bridge mode selector switch per channel pair
- 4 balanced line inputs and 4 speaker outputs with terminal block connections
- User-friendly front panel with signal, limit, protection, mute and bridge mode LEDs per channel and clipping LEDs for the inputs
- Speaker protection circuits: DSP limiter, overcurrent, direct current, overheating, short circuit as well as switchable auto standby mode
- DSP presets with HPF and LPF which can be activated via DIP switches
- REMOTE audio and control bus based on CAN architecture (Controller Area Network)
- Equipped for future LD Systems remote control panels and paging microphones
- Slot for future optional expansion cards for Ethernet or Ethernet + Dante
- Optional accessories: 19" L-bearing rails, length 450 mm
LD Systems IPA412T Specifications:
- General
- Product type: Amplifier
- Type: Installation power amplifier
- General data
- Audio Channels: 4
- Output Circuitry: Class D
- Operating voltage: Wide Range SMPS with PFC (power factor control)
- Mains connector: IEC socket
- Auto-Standby Power: Yes. Switchable (On-Off)
- Time to Auto-standby: 20 Min with no audio input signal
- DSP: Yes
- Remote-Bus: Yes
- Indicators: Front Panel: "PROT", "LIMIT", "SIG", "BRIDGE" and Mute Symbol LED´s. Power On/ Standby LED, Rear Panel: 4x Input Clip LED´s, Remote Lock LED (Red)
- Controls Front panel On / off switch, standby
- Controls Element Back Panel: "BRG“ (Bridge), "PAR“ (Parallel), "ST“ (Stereo), Amplifier Channel Mode, Low-Z and High-Z switches (paired), Output Volume potentiometers, Preset A and B switches, Remote Lock, Remote ON/OFF, Remote-Mode, Standby On/Off
- Inputs: 4x Balanced Line Inputs, Remote Bus Audio Input
- Input connectors: 6-pin Terminal Block Pitch 3.81mm, Remote IN/OUT RJ45, Service Micro USB Type-B
- Expansion Slot: For optional Ethernet, or Ethernet + Dante cards
- Cooling: front to rear/side airflow, Passive + 2-zone temperature controlled active cooling
- Operating voltage: 100 V AC - 240 V AC, 50 - 60 Hz
- Fuse: T10AL 250 V
- Inrush Current Power OFF-Standby: 2.8 A
- Inrush Current Standby-ON: 0.5 A
- Power Consumption @ Standby: 0.9 W
- Power Consumption @ idle mode: 25 W
- Power Consumption @ full load: 790 W
- Operating temperature: 0 °C - 40 °C; (max 60% relative humidity)
- Width: 483 mm
- Height: 44.5 mm
- Depth: 425 mm
- Optional accessories: 19" L mounting rails ( AH - 876TL )
- Weight: 8,7 kg
- Amplifier Output Specifications, all outputs driven and loaded
- Rated ouput power (1kHz @ 4 Ohms): 4 x 120 W (1,5 Seconds Sine Burst)
- Rated ouput power (1kHz @ 8 Ohms): 4 x 60 W (1.5 Seconds Sine Burst)
- Rated ouput power (1kHz @ 16 Ohms): 4 x 30 W (1,5 Seconds Sine Burst)
- Rated ouput power (1kHz @ 8 Ohms, bridged): 2 x 235W (1,5 Seconds Sine Burst)
- 4 x 240W, Transformer Coupled Output 4 x 120W, Transformer Coupled Output
- Protection circuits: Audio Limiter, DC, HF Protect, HPF (High-Z), short circuit, temperature, thermal overload
- Minimum load impedance per channel: 4 ohms Single-Ended, 8 ohms Bridge
- Performance specifications
- Nominal input sensitivity: +5 dBu (Sine 1 kHz, Gain max)
- Nominal input clipping: 19 dBu (Sine 1kHz)
- THD + N: < 0,03 % (Low-Z SPK OUT, +18 dBu, 20 Hz – 20 kHz)
- Frequency response: 18 Hz – 22 kHz (Low-Z OUT, -3 dB), 50 Hz – 23 kHz (High-Z OUT, -3 dB)
- Signal-to-noise ratio: >105 dB (Low-Z SPK OUT, CH Gain Center (0 dB), 20 kHz BW, a-weighted)
- Crosstalk: 83 dB @ 1 kHz
- Digital Specifications
- System Latency: 6.2 ms
- AD/DA converter resolution: 24 bit
- AD/DA converter sampling rate: 48 kHz
