Product Overview
The HD-MD-4K-400 from Crestron offers an economical solution for delivering multimedia presentations in educational settings and conference rooms. It comprises of two components - the transmitter (HD-TX-301-C-E) and the receiver (HD-RX-4K-210-C-E) - that allow you to transmit HDMI® or VGA signals over a CATx (CAT5e or higher) cable. With resolutions up to 2K, the transmission distance reaches up to 230 feet (70 meters), while for higher resolutions up to 4K, the transmission distance is limited to 130 feet (40 meters). The transmitter boasts two HDMI inputs and one VGA input, complete with a stereo analog audio input. Meanwhile, the receiver offers an additional HDMI input, which can be used to connect to a nearby AV source or an optional Crestron media presentation wall plate (sold separately as MP-WP152).
NOTE: Power is transmitted over the CATx cable that connects the transmitter to the receiver.
Crestron HD-MD-4K-400 Kit Features:
- Automatic Switching of Inputs
- HDMI Output with 4K Scaler, 4K/60 4:2:0 capability
- Audio De-embedding
- Device Control
- .AV Framework Technolog Support
- XiO Cloud Service Support
- Native Integration with Cisco Webex and Touch 10 devices
- Low-profile Installation
- Two HDMI® inputs and one VGA input on transmitter and an additional HDMI input on receiver
- HDCP and EDID management
- Gigabit ethernet connectivity
- CEC capability
- Signal extension of video, audio, and power over a CATx cable—up to 230 ft (70 m) for resolutions up to 2K or up to 130 ft (40 m) for higher resolutions up to 4K
Crestron HD-MD-4K-400 Kit Specifications:
- Video
- Switcher: 4x1 (3 inputs at transmitter plus 1 input at receiver x 1 output at receiver) auto-switching or manual, audio-follows-video, Crestron Auto-Locking® and QuickSwitch HD™ technology
- Scaler, HDMI Output: 4K video scaler with intelligent frame rate conversion, Deep Color support, content adaptive noise reduction, 3:2/2:2 pull-down
- detection and recovery
- Input Signal Types: HDMI with Deep Color and 4K (DVI and Dual-Mode DisplayPort™ interface compatible2); VGA/RGB (RGBHV, RGBS, RGsB), component (YPbPr)3
- Output Signal Types: HDMI with Deep Color and 4K (DVI compatible4)
- Copy Protection:
- Transmitter: HDCP 1.4
- Receiver: HDCP 2.2
- Audio:
- Input Signal Types: HDMI (Dual-Mode DisplayPort interface compatible2), analog stereo
- Output Signal Types: HDMI, analog stereo
- Digital Formats: 2-channel LPCM
- Analog Formats: Stereo 2-channel
- Analog-To-Digital Conversion: 24-bit 48 kHz
- Digital-To-Analog Conversion: 24-bit 48 kHz
- Output Impedance: 200 ohms balanced, 100 ohms unbalanced
- Maximum Output Level: 4 Vrms balanced, 2 Vrms unbalanced
- Output Volume: -80 to +20 dB level adjustment range, plus Mute
- Mute: Enable or disable independently for HDMI and analog audio output
- Analog Input Performance: Frequency Response: 20 Hz to 20 kHz ±0.5 dB;
- S/N Ratio: >93 dB, 20 Hz to 20 kHz A-weighted;
- THD+N:
- Stereo Separation: >80 dB
- Analog Output Performance: Frequency Response: 20 Hz to 20 kHz ±0.5 dB;
- S/N Ratio: >95 dB @ 10 dBV, 20 Hz to 20 kHz, A-weighted
- THD+N:
- Stereo Separation: 20 Hz to 20 kHz ≤80 dB
- Acoustic Noise: Not applicable (fanless)
- Communications:
- Ethernet: 100/1000 Mbps, auto-switching, auto-negotiating, auto-discovery, full/half duplex, CIP, DHCP, web browser setup and control
- RS-232: 2-way device control and monitoring up to 115.2k baud with hardware and software handshaking
- IR: 1-way device control via infrared up to 60 kHz
- HDMI:
- Transmitter: HDCP 1.4, EDID
- Receiver: HDCP 2.2, EDID, CEC
- USB: USB host for one Crestron TT-100 Series Cable Caddy (sold separately)
- DM Lite: HDCP 2.2, EDID
- Controls and Indicators (transmitter):
- TO RX (DM Lite): (2) LEDs on RJ-45 connector. Green LED indicates DM Lite link status. Amber LED indicates a valid video signal.
- PWR: (1) LED, indicates that power is being applied to the HD-TX-301-C-E from the power pack connected to either the HD-TX-301-C-E or the receiver. Amber indicates that the HD-TX-301-C-E is booting. Green indicates that the HD-TX-301-C-E is operational.
- AUTO: (1) Push button to enable or disable automatic switching and (1) green LED to indicate that automatic switching is enabled
- INPUT 1 – 3: (3) Push buttons for manual input selection and (3) bi-color green/amber LEDs to indicate the current active input and signal presence at each corresponding input
- SETUP: (1) Red LED and (1) recessed pushbutton for Ethernet setup
- Controls and Indicators (receiver):
- PWR: (1) LED, indicates that power is being applied to the HD-RX-4K-210-C-E from the power pack connected to either the HD-RX-4K-210-C-E or the transmitter. Amber indicates that the HD-RX-4K-210-C-E is booting. Green
- INPUT 1 – 2: (2) Push buttons for manual input selection and (2) LEDs. Green indicates that video is switched. Amber indicates that video is detected but is not switched.
- AUTO: (1) Push button to enable or disable automatic switching and (1) green LED to indicate that automatic switching is enabled
- SETUP: (1) Red LED and (1) push button for display of IP address on the HDMI output
- DM Lite: (2) LEDs on RJ-45 connector. Green indicates that a DM Lite link is established. Flashing amber indicates non- HDCP video, and solid amber indicates HDCP video.
- Ethernet: (2) LEDs on RJ-45 connector. Green indicates that an Ethernet link is established. Flashing amber indicates Ethernet activity.
- Power:
- Power Pack:
- (Included with Transmitter and Receiver)
- Input: 100-240 VAC, 50/60 Hz
- Output: 1.25 A @ 24 VDC
- Model: PW-2412WU
- Power Consumption: 18.5 W typical
- Environmental:
- Temperature: 32° to 104° F (0° to 40° C)
- Humidity:
- Transmitter: 20% to 90% RH (non-condensing);
- Receiver: 10% to 90% RH (non-condensing)
- Heat Dissipation: 63.1 BTU/hr
- Enclosure:
- Chassis: Metal, black finish, vented sides, 2 mounting flanges
- Mounting: Surface or rack rail mount
- Dimensions:
- Transmitter (HxWxD): 1.11 x 7.0 x 5.12 in
- Receiver (HxWxD): 5.11 x 10.53 x 1.1 in
- Weight:
- Transmitter: 20.0 oz (567 g)
- Receiver: 2.3 lb (1.05 kg)
- Compliance: UL® Listed for US and Canada, CE, IC, FCC Part 15 Class B digital device
Full Specs under Documentation tab
