Product Overview
Extend 4K video signals and they're supported audio up to 130 ft with Crestron's HD-TX-201-C-2G-E-W-T HDMI over CATx transmitter and 2x1 auto-switcher wall plate. The HD-TX-201-C-2G-E-W-T also extends HD 1080p, WUXGA, and 2K signals up to 230 ft over CAT5e or higher cabling. HDMI, VGA, and audio inputs offer standard connections with auto-switching between HDMI and VGA providing plug-and-play simplicity. A CAT6a RJ-45 courtesy jack is included to provide a 1000BASE-T network connection for computers and other devices.
Crestron HD-TX-201-C-2G-E-W-T Includes:
- DM Lite Multiformat Switch and Transmitter
Crestron HD-TX-201-C-2G-E-W-T Features:
- Pairs with a DM Lite® or DMPS Lite™ receiver
- Enables extension of HDMI® video and audio signals
- Converts and extends VGA and analog audio signals
- Auto-switches between one HDMI input and one VGA input
- Links to the receiver via a single CAT5e (or higher) twisted pair cable
- Supports 4K and UHD at up to 130 ft (40 m)
- Supports HD 1080p, WUXGA, and 2K at up to 230 ft (70 m)
- Handles 4K video resolutions up to 4K60 4:2:0 and 4K30 4:4:4
- Handles 3D video and Deep Color
- Supports Dolby® TrueHD, Dolby Atmos®, DTS HD®, DTS:X®, and uncompressed 7.1 linear PCM audio
- Compatible with HDMI, DVI, and Dual-Mode DisplayPort™ sources
- Compatible with VGA, RGBHV, RGBS, RGsB, and YPbPr component sources up to HD 1080p and WUXGA
- HDCP 1.4 compliant
- Passes CEC and EDID signals
- Allows control system integration when paired with an HD-RX-201-C-E or DMPS Lite receiver
- Courtesy LAN jack
- Flush wall mount design
- Installs in a 2-gang U.S. electrical box (2-1/4” deep) or plaster ring (not included)
- Decorator style faceplates sold separately (type FP-G2-DM only)
- Normally powered by the receiver (surface-mountable) over the link cable
Crestron HD-TX-201-C-2G-E-W-T Specifications:
- Switcher: 2x1 manual or auto-switching, audio-follow-video
- Input Signal Types: HDMI with Deep Color, 3D, and 4K (DVI and Dual-Mode DisplayPortTM interface compatible), VGA/RGB (RGBHV, RGBS, RGsB), component (YPbPr)
- Copy Protection: HDCP 1.4
- Maximum Resolutions
- HDMI:
- Progressive
- 4096x2160 DCI 4K & 3840x2160 4K UHD
- 24 Hz, 4:4:4, 30 bit
- 30 Hz, 4:4:4, 24 bit
- 30 Hz, 4:2:2, 36 bit
- 60 Hz, 4:2:0, 24 bit
- 2560x1600 WQXGA
- 60 Hz, 4:4:4, 36 bit
- 1920x1080 HD 1080p
- 60 Hz, 4:4:4, 36 bit
- Interlaced
- 1920x1080 HD 1080i
- 30 Hz, 4:4:4, 36 bit
- VGA/RGB:
- Progressive
- 1600x1200 UXGA, 60 Hz
- 1920x1200 WUXGA, 60 Hz
- Component
- Progressive
- 1920x1080 HD 1080p, 60 Hz
- Interlaced
- 1920x1080 HD 1080i, 30 Hz
- NOTE: Common resolutions are shown; other custom resolutions are supported at pixel clock rates up to 300 MHz for HDMI or 165 MHz for VGA.
- Audio
- Input Signal Types: HDMI (Dual-Mode DisplayPort interface compatible), analog stereo
- Digital Formats: Dolby Digital®, Dolby Digital EX, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos, DTS®, DTS ES, DTS 96/24, DTS HD High Res, DTS-HD Master Audio, DTS:X, LPCM up to 8 channels
- Analog Formats: Stereo 2-channel
- Analog-To-Digital Conversion: 24-bit 48 kHz
- Analog Performance:
- Frequency Response: 20 Hz to 20 kHz ±0.75 dB;
- S/N Ratio: >90 dB, 20 Hz to 20 kHz A-weighted;
- THD+N:
- Stereo Separation: >80 dB
- Communications
- HDMI: HDCP 1.4, EDID, CEC pass-through
- DM Lite Link: Proprietary link for connection between one DM Lite transmitter and receiver only
- NOTE: Supports management of HDCP and EDID only when paired with an HD-RX-201-C-E or DMPS Lite receiver; supports management of CEC between the connected HDMI device and a control system only when paired with an HD-RX-201-C-E or DMPS Lite receiver.
- Connectors
- HDMI IN:
- (1) HDMI Type A connector, female
- HDMI digital video/audio input (DVI and Dual-Mode DisplayPort interface compatible)
- VGA IN:
- (1) HD15 connector, female
- RGB (VGA) or component video input
- Formats: RGBHV, RGBS, RGsB, and YPbPr
- AUDIO IN:
- (1) 3.5 mm TRS mini phone jack
- Unbalanced stereo line-level audio input
- Maximum Input Level: 2 Vrms
- Input Impedance: 44k Ohms
- LAN (Front):
- (1) 8-pin RJ-45 connector, female
- Passive pass-through to the rear panel LAN jack
- See "LAN (Rear)" specifications below
- SERVICE (Right Side):
- (1) USB Type A connector, female
- For factory use only
- TO RX (DM Lite, Rear):
- (1) 8-pin RJ-45 connector, female, shielded
- DM Lite link port for connection to a DM Lite or DMPS Lite receiver
- 24VDC 1.25A (Rear):
- (2) Captive screw terminals
- 24 VDC power input
- Power pack sold separately (if required, model TBA)2
- NOTE: This connection powers both the transmitter and receiver; this connection is not normally used when pairing with a surface-mountable receiver.2
- LAN (Rear):
- (1) 8-pin RJ-45 connector, female
- Passive pass-through to the front panel LAN jack
- Compatible Cable Standards: CAT5e, CAT6, and CAT6a
- Low Level Contact Resistance: 100 mΩ maximum
- Insulation Resistance: 500 mΩ minimum at 500 VDC
- Dielectric Withstanding Voltage: 1000 VAC between contacts and shell
- Voltage Rating: 125 VAC
- Current Rating: 1.5 Amps
- PoE Compatibility: IEEE 802.3at PoE and PoE+
- Insertion Force: 22 N maximum
- Retention Force: 76 N minimum
- Controls and Indicators
- PWR: (1) Bi-color green/amber LED, indicates operating power is supplied from the receiver via the DM Lite link or from a power pack via the 24 VDC input, turns amber while booting and green when operating
- HDMI IN: (1) Bi-color green/amber LED, indicates HDMI input selection and signal presence
- VGA IN: (1) Bi-color green/amber LED, indicates VGA input selection and signal presence
- INPUT SEL: (1) Push button for manual input selection, cycles through all available inputs on both the transmitter and receiver
- AUTO: (1) Push button to enable/disable auto-switching mode, and (1) green LED to indicate auto-switching mode is enabled
- SETUP: (1) Red LED and (1) recessed push-button for Ethernet setup (only when paired with an HD-RX-201-C-E or DMPS Lite receiver)
- LINK: (1) Green LED, indicates the DM Lite link status
- RESET: (1) Push button for hardware reset (Resets both the transmitter and receiver when paired with an HD-RX-201-C-E or DMPS Lite receiver)
- TO RX (DM Lite, Rear): (2) LEDs on RJ-45 connector, green LED indicates DM Lite link status, amber LED indicates a valid video signal
- Power
- Power Pack (sold separately):
- Input: 100-240 VAC, 50/60 Hz;
- Output: 1.25 Amps @ 24 VDC;
- Model: TBA
- Note: This power pack is required only when the HD-TX-201-C-2G-E is paired with a wall plate receiver. When the HD-TX-201-C-2G-E is paired with a surface-mountable receiver, the power pack included with and connected to the receiver is used to power both the receiver and the HD-TX-201-C-2G-E.2
- Environmental
- Temperature: 32° to 104° F (0° to 40° C)
- Humidity: 20% to 90% RH (non-condensing)
- Heat Dissipation: 20.1 BTU/hr
- Construction
- Composition: Metal housing and bracket with black or white polycarbonate front label overlays
- Mounting: Mounts in a 2-gang, 2-1/4 inch (57 mm) deep U.S. electrical box or plaster ring (not included)
- Faceplate: Requires a Crestron FP-G2-DM-B-T or FP-G2-DM-W-T faceplate (sold separately, other faceplates are incompatible)
- Dimensions (HxWxD): 4.19" x 3.50" x 2.07" (107 x 89 x 53 mm)
- Weight: 8.9 oz (252 g)
- Compliance
- UL® Listed for US and Canada, CE, IC, FCC Part 15 Class B digital device
- Regulatory Models: HD-TX-201-C-2G-E-B-T, HD-TX-201-C-2G-E-W-T