Aviom MIX320-D Personal Mixing System with Dante Interface

Aviom’s Mix320-D Personal Mixing System has been designed specifically for use with Dante™ enabled consoles and networks. It includes everything you need to create a personal mixing system for six performers who have their own in-ear monitors. The A320 Personal Mixers get their digital data and power over the same cable, so all you need to do is connect a Cat-5 cable and you're ready to start using the system. The Mix320-D Personal Mixing System makes it easy to add Aviom monitoring to a Dante-enabled mixing console or audio network. No analog input module or console card is required; inputs get patched directly from your Dante network.

The Mix320-D system includes a D400-Dante A-Net Distributor that allows up to 32 channels to be patched from the Dante network to the personal mixing system inputs. The D400-Dante is also used to supply A-Net digital data and DC power to the mixers. The Mix320-D system includes six A320 Personal Mixer for the performers, plus six MT-1a Mic Stand Mounts for attaching the A320 mixers to mic stands, as well as all the Cat-5e cables you'll need to connect the products.

The A320 Personal Mixer gives performing and recording musicians simple, intuitive control over their monitor mixes. It features a 32-channel mix engine with 16 mono or stereo mix channels buttons and easy to use Stereo Placement controls.

Connect headphones, ear buds, or a wireless in-ear monitoring system to the Personal Mixer and you're ready to start mixing.

For distributing the A-Net digital data and DC power to the A320 Personal Mixers, the system includes the D400-Dante A-Net Distributor. The D400-Dante also serves as the system's input device; it allows up to 32 channels from your Dante network to be assigned to the eight powered A-Net ports on its front panel. Stereo Link switches allow adjacent channels to be treated as a stereo pairs on the A320 Personal Mixers where they will appear on a single mix channel button.

The Mix320-D system uses a Dante network for its inputs. If you use a digital console, check out the Mix320-Y Personal Mixing System which includes a Y1 card for Yamaha® consoles for its inputs. Or, if you have an analog console or recording system, the Mix320-A Personal Mixing System is what you need. It includes the 16-channel, line-level AN-16/i Input Module as its front end. The mixing system packages are also easy to expand when you're ready—just add more Personal Mixers and A-Net Distributors as needed.

Note: The Mix320-D system does not come with in-ear monitors.

Includes

• (1) D400-Dante A-Net Distributor
• (6) A320 Personal Mixers
• (6) MT-1a Mic Stand Mounts
• (7) Cat-5e cables

A320 Specifications

• Audio Output: 1/4" TRS stereo, headphone or line level
• Stereo Mix Output, Headphone/Line:
  • Tip: Audio Left
  • Ring: Audio Right
  • Sleeve: Ground
• A-Net I/O: 1 A-Net In, RJ45 connector; Supports Pro16 and Pro16e
• D/A Conversion: 44.1/48 kHz, 24-bit
• Stereo Operation:
  • Stereo Link, per channel pair
  • Set at the input module
  • Variable pan per mono channel or pan/spread per stereo channel pair
• Headphone Output: 275 mW per side into 50 Ω (both sides driven)
• Output Impedance: 5 Ω
• Freq. Response: 3 Hz - 22 kHz +0.2 dB/-3 dB at 50 Ω
• THD +N: < 0.003%
• Output Voltage for Personal Mixers:
  • 24VDC, 0.5 amp
  • Transmitted over the Cat-5e cable
• Signal to Noise (unweighted): -106 dB (measured with zero data into all channels)
• Latency: 0.880 msec (measured from analog input to analog output)
• Pro16e A-Net:
  • Use Cat-5e (or better) cable
  • Maximum 400ft (122m) between devices
  • Supports Power Over A-NetCat-5 cable: Use shielded Cat-5e (or better) cable to stay below the CISPR 22 Class B, ICES-003, and FCC 47 CFR Part 15 Class B emissions limits.
• Power:
  • 24 VDC, 0.5 amp
  • Power is supplied over the Cat-5 cable when connected to an Aviom A-Net Distributor
• Dimensions (W x D x H): 10.26" x 6.14" x 1.91" (260.6 x 155.95 x 48.51 mm)
• Weight: 1.3 lbs. (0.59 kg)
• Options: MT-1a Mic Stand Mount

D400-Dante Specifications

• Dante Interface: 32 channels (44.1/48 kHz Sample Rate)
• Dante Primary I/O: RJ45 connector
• Dante Secondary I/O: RJ45 connector
• Dante LEDs: Network Activity (green); 1GB Network Connection Active (yellow)
• A-Net Out to Personal Mixers: Eight RJ45 connectors, powered
• A-Net Out:
  • Pro16e A-Net
  • RJ45 connector, unpowered
• LEDs: Power On (red); Network Sync (green)
• Stereo Link: Two 8-position DIP switch blocks (1-16,17-32)
• Output Voltage for Personal Mixers:
  • 24VDC, 0.5 amp
  • Transmitted over the Cat-5e cable
  • A-Net Cables: Front Panel Connections: Shielded Cat-5e (or better) cable must be used to stay below the CISPR 22 Class B, ICES-003, and FCC 47 CFR Part 15 Class B emissions limits. Unshielded Cat-5e cable may be used on all rear panel connections
• Power Supply: Internal, IEC connector
• Input Voltage: 100-120 VAC or 200-240 VAC (with selector switch); 50-60Hz @220 W max
• AC Fuse Types:
  • 115V range: T2.5AL/250V
  • 230V range: T1.25AL/250V
• Dimensions (W x D x H): 19" x 7.386" x 2U, 3.5" (482.6 x 187.6 x 88.9mm)
• Weight: 12 lbs. (5.44 kg)