Product Overview
The DM™ 115 from Peavey® is a 15" 2-way powered loudspeaker with onboard DSP that is part of the Dark Matter™ Series of powered loudspeakers. This series features modern styling, and thanks to their advanced DSP, these enclosures deliver best-in-class performance.
Features
- Two way, bi-amplified analog amp powered speaker system
- 15" heavy-duty woofer
- DX 14 compression driver with 1.4" titanium diaphragm
- 410 Watts peak dynamic woofer power
- 250 Watts peak dynamic tweeter power
- Fan-cooled for maximum reliability
- Patented Quadratic Throat Waveguide technology
- Rear LCD display for selection of DSP control parameters, such as EQ presets, plus Bass and Treble controls
- 110° x 80° coverage
- Input is via a balanced XLR-¼" combo jack
- Mic/Line switch provides for two different gain settings
- Thru output is via a male XLR jack
- Rugged plastic injection-molded trapezoidal enclosure
- Cabinet has rear corner angled sides for floor monitor use
- Full-coverage perforated steel grille with powder coat finish
- Pole mount molded-in for 1-3/8" diameter poles
- Weight: 42 lbs. (19 kg)
- Dimensions (H x W x D): 27.974" x 16.75" x 15.06" (709.68 x 425.5 x 382.6mm)
Specifications
- General:
- Frequency Response: 62 Hz to 19 kHz, +/- 6 dB, anechoic environment
- Usable Low Frequency limit (-10 dB point anechoic): 52 Hz
- Nominal sensitivity (1 W @ 1 m, swept sine input in anechoic environment): 96 dB (average)
- Maximum Sound Pressure Level (1 meter): 124 dB SPL peak with music
- Radiation Angle measured at -6 dB point of polar response: Nominal: 110 degrees horizontal X 80 degrees vertical (Axis of the vertical main polar lobe is angled down 10 degrees, resulting in the angular pattern with respect to straight ahead being 30, -50 degrees)
- Transducer Complement: Heavy-duty 15" woofer with 2" voice coil and 44 oz. magnet
- DX 14 1.4" titanium diaphragm dynamic compression driver
- Box Tuning Frequency: 53 Hz
- Electroacoustic crossover frequency: 3,000 Hz
- Crossover type: Internal Electronic DSP based two-way crossover with driver EQ, level matching, bass boost, limiting and subsonic filtering
- Crossover Slopes: 24 dB/octave (4th-order) low pass, 24 dB/octave (4th-order) high pass, both with staggered poles and driver EQ
- Input Connections: One combo female XLR-¼" phone jack providing balanced line-level operation from the ¼" jack section, and the XLR section.
- Output Connections: One male XLR jack. The Thru jack is intended for the use of linking multiple DM 115‘s in a line or to provide a feed to a powered subwoofer, or other electronics that needs to receive a full range version of the input signal
- Enclosure Materials and Finish: Black polypropylene plastic with textured surface, black powder-coated perforated full-coverage grille
- Mounting provisions: Four rubber feet provide vibration free floor or stage use, and a molded-in stand mounting cup is on the bottom. Unit is not designed to be flown overhead
- Physical:
- Overall Dimensions (H x W x D): 28.3" x 16.75" x 15.00" (719 x 426 x 381mm)
- Weight: 42 lbs. (19.1 kg)
- Electronics and Amplifier:
- Internal power amplifiers (@120 VAC line): Total of 660 Watts peak dynamic power; Woofer - 410 Watts peak dynamic power; Continuous Power: 125 Watts @ less than 1% distortion; Tweeter - 250 watts peak dynamic power; Continuous Power: 80 Watts @ less than 1% distortion
- Electronic Input Impedance (Nominal): Line: 4.5 kΩ balanced (XLR or ¼"); Mic: 4.5 kΩ balanced (XLR) No phantom power available
- Input Sensitivity for Full Output (Level full CW): 0.39 V RMS (Switch in LINE position)
- Input Overload Point (Switch in LINE position): +17 dBV
- Infrasonic filter protection: 36 dB/octave roll-off
- Nominal Amplifier Frequency Response: +1, -3 dB from 20 Hz to 20 kHz
- Hum and Noise: Greater than 90 dB below rated power
- THD and IM: Typically less than 0.7 %
- Power requirements: Nominal 170 Watts, 120 VAC 60 Hz
- Fuse Type: for 120 VAC USE: International fuse classification T4AH 250V. In the USA, types GDC, GMC, 215, 218, and 477 cartridge-style 5x 20mm size fuses with a 4 Amp 250 V rating can be used; for 220-240VAC USE: International fuse classification T2AHL 250V . This is a cartridge style 5x 20mm size time-delay fuse with a 2 Amp 250 V rating