Product Overview
AMX's DXLink Multi-Format Wallplate Transmitter sends analog or digital video including HDMI/HDCP, along with embedded audio or supplemental analog audio up to 100 meters to an Enova DGX Digital Media Switcher, compatible Enova DVX All-In-One Presentation Switcher, or directly to a DXLink Receiver. It receives Power over DXLink* from the Enova DGX, Enova DVX (3155HD, 3156HD or 2155HD), PS-POE-AT-TC High Power PoE Injector or PDXL-2 Dual Power over DXLink Controller over the twisted pair cable and features both a multi-format analog port to support legacy devices and an HDMI port to support newer digital devices.
AMX FG1010-320-BL common applications:
Mount the DXLink Multi-Format Wallplate Transmitter in the wall or lectern to connect guest equipment and send audio and video signals across the room, on the other side of the house or in a classroom down the hall. Since it is powered remotely, the wallplate can be installed virtually anywhere.
AMX FG1010-320-BL Features:
- Only One Cable - Send audio and video, while passing Ethernet signals and power over one twisted pair cable
- Multi-Format Analog Port and HDMI Port - Supports legacy analog signals - RGBHV, Component, S-Video, and Composite, and digital HDMI/HDCP, Display Port++ and DVI signals
- Send HDMI signals up to 100 meters – Extend the reach of the HDMI signals far beyond the capabilities of typical HDMI cabling
- Standard Twisted Pair Cable – Save time and effort in installation by leveraging cost effective twisted pair cable, see the white paper titled Cabling for Success with DXLink for more details
- Power over DXLink* Enabled – Designed for use with Enova DGX or DVX systems with DXLink inputs, PS-POE-AT-TC (FG423-84) or PDXL-2(FG1090-170) to provide remotely located Power over DXLink (requires firmware v1.2.40 or above)
- DXLink Direct Connection – When receiving Power over DXLink* from the PS-POE-AT-TC or PDXL-2, DXLink Wallplates can be connected directly to a DXLink Receiver for a point-to-point solution
- Power Remotely - Power over DXLink* is carried over twisted pair to simplify installation when used with the Enova DGX, Enova DVX,PS-POE-AT-TC or PDXL-2
- 3D Support - Pass through latest video formats including 3D and Deep Color
- Surround Sound Support - Pass through high definition surround sound including Dolby Digital, DTS and up to 8-channel L-PCM at 32kHz, 44.1 kHz, 48 kHz, 96 kHz, 192kHz
- HDCP Compliant
- * Power must be supplied by one of the following DXLink Power sourcing devices: Enova DGX 8/16/32/64 Digital Media Switcher (with a DXLink Twisted Pair Input Board installed), Compatible Enova DVX All-In-One Presentation Switcher (3155HD, 3156HD or 2155HD), PS-POE-AT-TC High Power PoE Injector or PDXL-2 Power over DXLink Controller. AMX only supports the use of these approved Power over DXLink solutions. Other third party power supplies or non-compatible standard PoE solutions may damage the DXLink equipment.
AMX FG-1010320-BL Specifications:
- GENERAL
- Dimensions (HWD): 4-11/16" x 6" x 1-5/16"(11.90 cm x 15.20 cm x 3.33 cm)
- Installation: Mounts onto standard 2 gang US, UK or EU back boxes
- Weight: 1.4 lb (0.64 kg)
- Shipping Weight: Approx. 2.2 lb (1.0 kg)
- Compatible AMX Products:
- Enova DGX 8/16/32/64 Digital Media Switchers
- Enova DVX-3155HD, DVX-2156HD and DVX-2155HDAll-In-One Presentation Switcher
- AVB-RX-DXLINK-HDMI DXLink HDMI Receiver Module as a point-to-point solution (when Wallplates are powered by PS-POE-AT-TC orPDXL-2)
- PS-POE-AT-TC High Power PoE Injector
- PDXL-2 Power over DXLink Controller
- Airflow: Natural convection via air vent openings on front, back and top
- MTBF: 381,000 hours
- Approvals:
- CE EN 55022, EN 55024 and EN 60950-1
- IEC 60950-1
- FCC
- UL 60950-1
- cUL
- RoHS/ WEEE compliant
- DXLink
- Transport Layer Throughput (Max): 10.2 Gbps
- Twisted Pair Cable Type: Shielded Cat6, Cat6A and Cat7
- Twisted Pair Cable Length: Up to 328 ft (100 m)
- ACTIVE POWER REQUIREMENTS
- Power must be supplied by a DXLink Power sourcing device such as:
- Enova DGX 8/16/32/64 Digital Media Switcher (with a DXLink Twisted Pair Input Board installed)
- Compatible Enova DVX All-In-One Presentation Switcher (3155HD, 3156HD or 2155HD)
- PS-POE-AT-TC High Power PoE Injector
- PDXL-2 Power over DXLink Controller
- Power Connector: Included on DXLink Connection
- Power Consumption (Max): Power over DXLink Supplied 7 W
- POWER SUPPLY
- Power must be supplied by a DXLink Power sourcing device such as:
- Enova DGX 8/16/32/64 Digital Media Switcher (with a DXLink Twisted Pair Input Board installed)
- Compatible Enova DVX All-In-One Presentation Switcher (DVX-3155HD, DVX-3156HD or DVX-2155HD)
- PS-POE-AT-TC High Power PoE Injector
- PDXL-2 Power over DXLink Controller
- ENVIRONMENTAL
- Temperature (Operating): 32° to 104° F (0° to 40° C)
- Temperature (Storage): -22° to 158° F (-30° to 70° C)
- Humidity (Operating): 5% to 85% RH (non-condensing)
- Humidity (Storage): 0% to 90% RH (non-condensing)
- Heat Dissipation (Max): Power over DXLink supplied: 24 BTU/HR
- FRONT CONNECTORS
- HDMI Input: HDMI Type A Female
- Analog Video Input: HD-15 (Breakout cable required for non RGB formats)
- Analog Stereo Input: 3.5mm Mini-Stereo Jack
- Advanced Configuration Interface**: USB Mini-B Connector
- USB (HID) Keyboard & Mouse**: USB Mini-B Connector
- SIDE CONNECTORS
- ID Pushbutton:
- Toggle between DHCP and static IP addressing
- Places system in NetLinx Device ID assignment mode
- Reset the factory default settings
- Restore the factory firmware image
- Reset Pushbutton: Resets/reboots the CPU of the wallplate
- BACK CONNECTORS
- CONTROL
- Advanced Configuration Interface**: USB Mini-B Connector
- INDICATORS
- Power Indicator: Green indicates whether or not the module is powered on
- HDMI
- Compatible Formats: HDMI, HDCP, DVI
- Input Signal Type:
- HDMI
- DVI-D (Single Link With Cable Adapter)
- Display Port ++ (Input Only, With HDMI Cable Adapter)
- Input Connector: HDMI Type A Female
- Propagation Delay (Typ): 5 us
- Input Voltage (Nominal): 1.0 Vpp Differential
- Input Re-clocking (CDR): Yes
- Input Equalization: Yes, Adaptive
- Data Rate (Max): 4.95 Gbps / 6.75 Gbps
- 6.75 Gbps supported when the DXLink HDMI RX Scaler is in Bypass mode and format is 1080p60 or less
- Pixel Clock (Max): 165 MHz / 225 MHz
- 225 MHz supported when the DXLink HDMI RX Scaler is in Bypass mode and format is 1080p60 or less
- Progressive Resolution Support: 480p up to 1920x1200 @60 Hz including but not limited to those resolutions shown in the DXLink Twisted Pair Transmitters/Receiver Instruction Manual
- Interlaced Resolution Support:
- Deep Color Support: 24-bit, 30-bit, 36-bit
- 30-bit, 36-bit supported when the DXLink HDMI RX Scaler is in Bypass mode and format is 1080p60 or less
- Color Space Support: RGB 4:4:4, YCbCr 4:4:4 and 4:2:2(Input signal support for YCbCr 4:4:4 and 4:2:2,output color-space is converted to RGB 4:4:4)
- 3D Format Support: Yes (HDMI Primary Formats)
- Frame Packing 1080p up to 24Hz
- Frame Packing 720p up to 50/60Hz
- Frame Packing 1080i up to 50/60Hz
- Top-Bottom 1080p up to 24Hz
- Top-Bottom 720p up to 50/60Hz
- Side-by-Side Half 1080p up to 50/60Hz
- Side-by-Side Half 720p up to 50/60Hz
- 3D supported when the DXLink HDMI Rx Scaler is in Bypass mode and format is 1080p60 or less
- Audio Format Support: Dolby TrueHD, Dolby Digital, DTS-HD Master Audio, DTS, 2 CH through 8 CH L-PCM Dolby Digital and DTS support up to 48kHz, 5.1 channels
- Audio Resolution: 16 bit to 24 bit
- Audio Sample Rate: 32 kHz, 44.1 kHz, 48 kHz, 96 kHz,192kHz
- Local Audio Support: Yes for audio insertion
- HDCP Support: Yes, supports AMX HDCP InstaGate ProTechnology when used with either an Enova DGX8/16/32 Digital Media Switcher orDVX All-In-One Presentation Switcher the key support is up to 16 sinks per output, independent of source device when used as a single point to point solution the key support is defined by the source device
- CEC Support: None
- DDC/EDID Support: The HDMI EDID in point to point mode is passed up from the sink device. When used with Enova DGX 8/16/32/64 Digital Media Switcher orEnova DVX-3155HD, DVX-3156HD or DVX-2155HD the HDMIEDID is passed from the Enova Switcher input to the TX and is user reprogrammable. The analog video input connection provides a fixed EDID set
- ANALOG VIDEO
- Compatible Formats: RGBHV, RGBs, RGsB; YPbPr (HDTV);Y/c (S-Video), C (Composite)
- Progressive Resolution Support: 480p up to 1920x1200@ 60 Hz (reference the DXLink Twisted Pair Transmitters/Receiver Instruction Manual for extended list)
- Interlaced Resolution Support: 480i, 576i, 1080i (reference DXLink Twisted Pair Transmitters/Receiver Instruction Manual for extended list)
- Auto-Adjust Input**: Supported
- RGB Input Signal Level Range: 1 Vpp nominal
- RGB Input Impedance: 75 ohms
- HV Sync Input Signal Level Range: 2 to 5 Vpp
- HV Sync Input Impedance: 2.5 pF Typ, 10 pF Max
- Digital Processing: 24 bit, 165 MHz
- Y/Pb/Pr Input Signal Level Range: 1.0 Vpp for Y, 700mVpp for Pb Pr
- Y/Pb/Pr Input Impedance: 75 ohms
- Y/c (S-Video) Input Signal Level Range: 1.0 Vpp forY, 1.0 Vpp for c
- Y/c (S-Video) Input Impedance: 75 ohms
- C (Composite) Input Signal Level Range: 1.0 Vpp
- C (Composite) Input Impedance: 75 ohms
- Input Connector: HD-15 (Breakout cable required for non RGBHV formats)
- AUDIO (ANALOG & DIGITAL S/PDIF)
- Input Signal Types: Stereo Analog, S/PDIF
- Video signal must be present to pass Audio
- Analog Input Level (Max): +2 dBu, unbalanced
- Analog Input Impedance: 10k ohms
- Analog to Digital Conversion: 48 kHz Sample Rate,24-bit
- S/PDIF Audio Format Support: Dolby Digital, DTS, 2 CHL-PCM; Dolby Digital and DTS support up to 48kHz, 5.1 channels
- S/PDIF Resolution: 16 to 24 bit
- S/PDIF Sample Rate: 32 kHz, 44.1 kHz, 48 kHz, 96 kHz
- S/PDIF Input Signal Level Range: 200 mVpp to 600mVpp terminated
- S/PDIF Input Impedance: 75 ohms
- Analog to Digital Reference Level: +2.5 dBu = 0 dBfs
- Input Connectors: 3.5mm Mini-Stereo Jack (Analog Stereo), RCA Jack (S/PDIF)
Note:
Specifications are subject to change.
** This feature will be available upon release of a future firmware update
AMX only supports the use of these approved Power over DXLink solutions. Other third party power supplies or non-compatible standard PoE solutions may damage the DXLink equipment. To use PS-POE-AT-TC or PDXL-2 as a power source the wall plates require firmware v1.2.40 or above
