Product Overview
The Peavey IPR2 7500 boasts 3750 watts RMS per channel at 2 ohms and is under 7kg. Featuring 2 channel independent fourth order Linkwitz-Riley crossovers, a variable-speed fan housed in a lightweight aluminum chassis, DDT speaker protection, and the revolutionary new IP-2 class D topology.
Peavey IPR2 7500 Features:
- 2 channel independent, fourth-order Link witz-Riley crossovers
- DDT protection
- Revolutionary IPR class D topology
- Detented input controls
- Combination XLR 1/4" inputs
- 4 pole twist lock output connectors
- Ultra-light weight
- Individual signal pass 1/4" jacks on each channel
- LED illuminated
- Standby, LED power present indication
Peavey IPR2 7500 Specifications:
- Rated Watts: 2ch x 2 ohms 4750 watts 20ms repetitive burst / 3750 watts 1% THD both channels driven @ 1 kHz.
- Rated Watts: 2ch x 4 ohms 2800 watts 20ms repetitive burst / 2450 watts 1% THD / 2020 watts 0.15% THD, both channels driven @ 1 kHz.
- Rated Watts: 2ch x 8 ohms 1550 watts 20ms repetitive burst / 1425 watts 1% THD / 1200 watts 0.15% THD, both channels driven @ 1 kHz.
- Minimum Impedance: 2 ohms
- Maximum RMS Voltage Swing: 124 volts
- Frequency Response: 20 Hz - 25 kHz; +0dB, -3dB
- 20 Hz - 20 kHz 2ch x 2 ohms:
- 20 Hz - 20 kHz 2ch x 4 ohms:
- 20 Hz - 20 kHz 2ch x 8 ohms:
- Input CMRR: > - 75dB @ 1 kHz.
- Voltage Gain: x 40 (+32dB)
- Crossover: 100Hz switchable 2nd order high pass and 3rd low pass per channel.
- Crosstalk: > -85dB @ 1kHz @ 1000 watts power @ 8 ohms.
- Hum and Noise: > -106dB, “A” weighted referenced to rated power @ 4 ohms.
- Slew Rate: > 12V/µs
- Damping Factor (8 ohms): > 200:1 @ 20Hz - 1kHz @ 8 ohms
- Input Sensitivity: 2.25 volts +/- 3% for 1kHz 4 ohm rated power, 2.195 volts +/- 3% for 1kHz 2 ohm rated power
- Input Impedance: 20 kilohms, balanced and 10 kilohms unbalanced.
- Current Draw: @ 1/8 in VA (watts) 2210 (1440) @ 2 ohms, 1550 (950) @ 4 ohms, 982 (560) @ 8 ohms
- Current DrawL @ 1/3 in VA (watts) 4260 (3150) @ 2 ohm,3120 (2160) @ 4 ohms, 1890 (1200) @ 8 ohms
- Idle Consumption: 250VA, 120 watts.
- Cooling: 3 temperature dependent variable speed fans.
- Controls: 2 front panel attenuators, crossover selectswitch for HPF, Normal and LPF
- Indicator LEDs: Five LED indicators per channel:Active, Signal, DDT, Temperature and DC
- Protection: Thermal, DC, subsonic, incorrect loads, under and over voltage
- Connectors:
- Inputs: Dual combination 1/4” XLR
- Outputs: Dual 1/4” thru, one 2-pin & one 4 pin twist-lock connector
- Construction: 0.062” thick aluminum
- Dimensions: 3.5”x19”x 17” behind front panel + 0.6” for handle
- Net Weight: 14.6lbs.* (6.61 kg)
- Gross Weight: 18.4lbs. (8.34 kg)
- Weight Unpacked: 14.57 lb (6.61 kg)
- Weight Packed: 18.39 lb (8.34 kg)
- Width Packed: 21" (53.34 cm)
- Height Packed: 21.2" (53.848 cm)
- Depth Packed: 6" (15.24 cm)
Note:
The IPR-7500 is a high-powered amplifier that requires a 20 amp supply to operate at full power and/or to drive a 2 ohm load. It ships with a 20-amp power cable that cannot be plugged into a standard 110V outlet. The IPR-7500 can be operated on a standard 110V supply if it is driving a load that is greater than 2 ohms or not operating at full power. Standard IEC power cable is NOT included and must be purchased separately. For more information on this and other products, contact your Sales Representative.
