Lectrosonics SPN1612 6x12 ASPEN Digital Mixer

Lectrosonics' 1612 Aspen Series mixer offers unlimited input expansion and 48 mix buses in order to give you superior scalibility. The Proportional Gain Algorithm provides seamless auto-mixing and integrates easily with with echo cancellation, analog mixing consoles, or any other type of audio system. And with TCP/IP addressibility for control through Ethernet, the 1612 is now part of your network.

Features:

• Ultra low noise input preamps
• Full crosspoint matrix with 48 outputs
• Unlimited input expansion
• TCP/IP Ethernet addressable
• Seamless auto-mixing with PGA™ at the matrixcrosspoints
• Simultaneous multi-point 3rd party and native control
• Ultra-low latency
• Automatic Master/Slave detection
• Single CAT6 interconnection carries data, audio and control signals

Specifications:

• Matrix: 48 mix buses with full output matrixing
• ASPEN port: 1Gbs control and audio data betweenASPEN units
• Inputs:
  • - 16mic/line
  • - Gain: 0 dB to 56 dB,programmable in 8 dBsteps (the analog gain is automatically selected by selecting the input gain)
  • - Input Level: 0 dBu nominal, max. 20dBu
  • - Input impedance: 8 k Ohms differential mode, 2 k Ohms common mode
  • - Phantom power: True 48Volt
  • - Dynamic range: 102 dB
  • - Ein: -127 dBu (20Hz – 20kHz,unweighted)
  • - THD + noise: 0.01%
• (All inputs are digitally programmable-gain microphone to line level differential inputs. Either side can be grounded or left floating. The cable shield shall be connected to ground.)
• Outputs:
  • - 1-8 line level (0 dBu), 9-12 mic/line level(0, -20, -40 dBu)
  • - Output level: 0 dBu nominal, max 20dBu
  • - Nominal level:
  • - 0 dBu,channels 1-8
  • - 0 dBu, -20 dBu, -40 dBu, channels 9-12
  • - Output impedance: < 50 Ohms, all outputs, all attenuator settings
  • - Dynamic range: 105 dB
  • - THD + noise: 0.01%
  • - Headroom: 20dB
• (All outputs are floating transformerless differential outputs. Either side can be grounded or left floating. The cable shield shall be connected to ground.)
• Latency: 1.46ms
• - Single-board: 64 audio samples = 1.333 ms
• -System: 64 + 6 (total number or boards – 1) audio samples = 1.333 + 0.125(total number or boards – 1) ms
• Programmable inputs: 30
• Programmable outputs: 16
• Frequency response: 20 Hz – 21 kHz ± 1 dB
• Monitor output (1/4" headphone jack): Any of the 48 final mixes
• Output power: 50 mW
• Filters: All filters, including the noise reduction filter (NRF), havezero processing delay.
  • - Noise reduction filters: Adjustable 6 to 35 dB onevery input
  • - Tone control stages: 4 per input channel
  • - Parametric EQstages: 8 per output channel
  • - ADFE: 8 per input channel
  • - Configurableas Static or Dynamic
• Filter types:
  • - Low Pass:
  • - Butterworth (6, 12, 18, 24dB/octave)
  • - Bessel (6, 12, 18, 24 dB/octave)
  • -Linkwitz-Riley (12, 24 dB/octave)
• - Additional parameters: frequency[Hz]
• - High Pass:
  • - Butterworth (6, 12, 18, 24dB/octave)
  • - Bessel (6, 12, 18, 24 dB/octave)
  • -Linkwitz-Riley (12, 24 dB/octave)
  • - Additional parameters: frequency[Hz]
• - Low Shelving:
  • - Butterworth (6, 12, 18, 24dB/octave)
  • - Bessel (6, 12, 18, 24 dB/octave)
  • - Additionalparameters: frequency [Hz], boost/cut [dB]
• - High Shelving:
  • -Butterworth (6, 12, 18, 24 dB/octave)
  • - Bessel (6, 12, 18, 24dB/octave)
  • - Additional parameters: frequency [Hz], boost/cut[dB]
  • - Peaking EQ (parametric) Parameters: frequency [Hz], bandwidth[octave], boost/cut [dB]
• Internal Signal Generator:
  • - White noise: Parameter: level [dBu]
  • -Pink noise: Parameter: level [dBu]
  • - Tone (sine wave): Parameters: level[dBu], frequency [Hz]
• Swept sine:
  • - Sweep modes: single sweep, continuous sweep
  • - SweepWaveform: sawtooth (up or down), triangle
  • - Sweep rate: linear, logarithmic
• Parameters: start frequency [Hz], stop frequency [Hz], level [dBu], sweeptime [sec]