Radio Design Labs STMDA3

Microphone Level Distribution Amplifier

OUR PART #: STMDA3 Write the First Review.

  • Feed 1 Microphone to 3 Microphone Inputs
  • Electrical and Audio Isolation
  • Studio Quality Low-Noise, Low-Distortion Performance
  • Excellent Phase Response
Learn More
Our Price: $145.20
List Price: $194.23
You save 25%!
Price-Matching Symbol. Low Price Guaranteed Free Shipping Available FREE Shipping
In Stock

Related Products

RDLs' STM-DA3 is designed for use in quality commercial sound, broadcast and recording applications. The 1.2 kOhm balanced input accepts a wide variety of microphone input levels without loading professional low impedance microphones. A multi-turn trimmer is user adjustable for either gain or loss in order to match the facility standard microphone levels. Three balanced outputs provide nearly total isolation between the output lines. Unlike mic-splitting transformer systems, the STM-DA3 also provides audio isolation. In fact, the audio isolation is so good that a +4 dBu signal fed into one output is still below the noise floor on the adjacent output. Loading of one output, including a direct short, has no effect on the other outputs.

The STM-DA3 is built on the electrical architecture of RDL's low- noise studio quality mic preamplifiers. Dynamic or condenser microphones may be used with the STM-DA3. Standard 24 V phantom is supplied to the input when the supply voltage is connected to the PHM terminal. Optimum operating level is set using RDL's unique Dual-LED VU meter, located adjacent to the terminal block. A green LED illuminates at 15 dB below optimum level. The intensity of the green LED progresses from minimum to full intensity over a 15 dB range. The adjacent red LED illuminates when the operating level exceeds the optimum level. This makes the STM-DA3 easy to set up without any external test equipment, and operating levels may be monitored at the module.

RDL STM-DA3 Features:

  • Feed 1 Microphone to 3 Microphone Inputs
  • Electrical and Audio Isolation
  • Studio Quality Low-Noise, Low-Distortion Performance
  • Excellent Phase Response
  • Versatility of STICK-ON® Compactness

RDL STM-DA3 Specifications:

  • Input: 1200 Ohm balanced
  • Outputs (3): -45 dBu, 150 Ohm balanced
  • Gain Range: 17 dB, 10-turn trimmer adjustable:
    • *Control fully CCW: Gain = -5 dB
    • * Control fully CW: Gain= 12 dB
  • Frequency Response: 30 Hz to 20 kHz (+/- 0.2 dB)
  • THD: < 0.1%
  • IMD: < 0.1%
  • Noise: < 80 dB (below -50 dBu output, -45 dBu input)
  • Headroom: > 20 dB (-50 dBu output, -50 dBu input)
  • CMRR: > 60 dB (100 Hz to 5 kHz)
  • Output Isolation: > 135 dB (balanced audio),> 150 dB (common mode)
  • Power Requirement: 24 - 33 Vdc @ 40 mA, Ground-referenced

Note:

Radio Design Labs' PS-24AS power supply is NOT included but is required in order to power this product. Please see the "Accessories" tab or click here for more information on the PS-24AS power supply.

Radio Design Labs STR-19A Rackmount System for 12 Stick-On Units

Radio Design Labs STR-19A Rackmount System for 12 Stick-On Units

Radio Design Labs' STR-19A Racking System holds up to 12 STICK-ONs in a 19" rack and only occupies two rack spaces.
$141.35 List Price: $189.08You Save 25%
In Stock
Free Shipping AvailableFree Shipping
Radio Design Labs PS-24AS 24 VDC 500mA Switching Power Supply, North American Model

Radio Design Labs PS-24AS 24 VDC 500mA Switching Power Supply, North American Model

Radio Design Labs' PS-24AS is a 24 VDC/500 mA switching power supply with a North American AC plug. Compatible with various RDL products.Radio Design Labs PS-24AS Specifications: Input: 100 to 240 VAC Output: 24 Vdc, 500 mA (UL, ...
$24.18 List Price: $32.35You Save 25%
In Stock
Radio Design Labs ST-RRB1 Mounting Bracket for STICK-ON Modules

Radio Design Labs ST-RRB1 Mounting Bracket for STICK-ON Modules

Radio Design Labs' ST-RRB1 mounting kit contains a bracket to attach a STICK-ON module to a rear rack rail or to any flat surface. The module slides into the holder and snaps into position. The module may easily be removed.
$23.44 List Price: $27.65You Save 15%
In Stock
Free Shipping AvailableFree Shipping
Radio Design Labs DRA-35S  Din Rail Adaptor for STICK-ON

Radio Design Labs DRA-35S Din Rail Adaptor for STICK-ON

The DRA-35S is a 35 mm DIN rail mounting bracket that provides positive mounting for any RDL STICK-ON® module. The oblique mounting angle of the DRA-35S allows an installer to mount several STICK-ON modules to a single DIN rail. Access to ...
$20.06 List Price: $23.67You Save 15%
In Stock
Radio Design Labs STR-19B Rackmount Kit for 10 Stick-On Units

Radio Design Labs STR-19B Rackmount Kit for 10 Stick-On Units

Radio Design Labs' STR-19B Racking System holds up to 10 STICK-ON unitss in a 19 inch rack and only occupies two rack spaces. The STR-19B holds STICK-ONs at an angle allowing for control adjustment from either the edge of a STICK-ON, or ...
$168.05 List Price: $224.79You Save 25%
Usually ships in 7-14 business days.
Free Shipping AvailableFree Shipping
Radio Design Labs SR-4 Mounting Frame for Stick/TX

Radio Design Labs SR-4 Mounting Frame for Stick/TX

Radio Design Labs' SR-4 is a universal module chassis that can mount to a backboard, wall or nearly any other support. It provides mounting for 4 STICK-ON power amplifiers or 7 standard STICK-ON modules. TX ™ modules may also be mounted. ...
$87.76 List Price: $117.39You Save 25%
Usually ships in 7-14 business days.
Free Shipping AvailableFree Shipping
Radio Design Labs SR-12A STICK-ON Series 19"W Mounting Rack for up to12 Modules

Radio Design Labs SR-12A STICK-ON Series 19"W Mounting Rack for up to12 Modules

Radio Design Labs' SR-12A chassis can be mounted in a rack or on a backboard to provide mounting of 12 STICK-ONs.
$67.63 List Price: $90.45You Save 25%
Usually ships in 7-14 business days.
Free Shipping AvailableFree Shipping
Radio Design Labs ST-PBR4 Mounting Bracket for up to 4 STICK-ON Modules

Radio Design Labs ST-PBR4 Mounting Bracket for up to 4 STICK-ON Modules

Radio Design Labs' ST-PBR4 is a mounting frame with slots for four STICK-ON modules.  The ST-PBR4 mounts on an FP-PSB1A power supply bracket or to any flat surface.  The ST-PBR4 design allows the installer to secure the modules ...
$35.78 List Price: $47.84You Save 25%
Usually ships in 7-14 business days.
Free Shipping AvailableFree Shipping
Radio Design Labs DRA-35S-6 6 Stick-On DIN Rail Adapter Modules

Radio Design Labs DRA-35S-6 6 Stick-On DIN Rail Adapter Modules

Radio Design Labs' DRA-35S-6 is a 35 mm DIN rail mounting bracket that provides positive mounting for any RDL STICK-ON® module.  The oblique mounting angle of the DRA-35S allows an installer to mount several STICK-ON modules to a ...
$33.98 List Price: $40.10You Save 15%
Usually ships in 7-14 business days.
Free Shipping AvailableFree Shipping
Radio Design Labs Smk 12 Mounting Strip for STICK-ON Units

Radio Design Labs Smk 12 Mounting Strip for STICK-ON Units

The SMK-12 allows removable surface (up to 6 units) or edge (typically 12, max. 16) mounting of STICK-ON units. They can be fastened to its surface using screws or adhesive foam pads.
$28.96 List Price: $38.73You Save 25%
Usually ships in 7-14 business days.
Free Shipping AvailableFree Shipping
Radio Design Labs Dtb Rdl Detachable Terminal Block

Radio Design Labs Dtb Rdl Detachable Terminal Block

Use DTB's to quickly detach and reattach wiring harness to STICK-ON units.
$7.15 List Price: $8.44You Save 15%
Usually ships in 7-14 business days.

Click to download

To be the first to review this item, click here.

Add to Cart

We're sorry, only of this item available



Call a Sales Pro at 800-356-5844 for more information