Panasonic PTFW430U
WXGA Installation Projector

Panasonic's FW430 Series projectors provide a reliable 6,000-hour lamp that is retrofit-friendly and easy to replace from the rear, while using inorganic, durable LCD panels that allow for a crisp, luminous picture quality.  With the addition of a dust-resistant cabinet and a new, reusable Eco Filter, the FW430 Series saves on time, money and maintenance by allowing up to 12,000 hours of operation before filter replacement is necessary.  And FW430 Series projectors offer greater installation flexibility than ever before with HDMI and DVI-I terminals that allow a wider range of input capabilities and features including a 2x Zoom Lens with horizontal/vertical Lens Shift that facilitates easy placement in a wide variety of rooms, and a new wireless application option that is compatible with the iPad, iPhone and iPod.  The Panasonic FW430 Series projectors fit the demands of any user, or any installation no matter what the requirements.

Specifications:

• Screen Size: 33"-300", 16:10 aspect ratio
• Optical Axis Shift: Vertical: ±51% from center of screen (manual), horizontal: ±27% from center of screen (manual)
• Lens: Manual (2x zoom), manual focus F 1.7-2.6, f 24.0-47.2 mm
• Power Supply: 100-240 V AC, 3.9 - 1.4 A, 50/60 Hz
• Power Consumption: 300 W (0.3 W at 100-120 V AC, 0.4 W at 220-240 V AC when standby mode set to eco,*1 9 W when standby mode set to normal, 20 W when standby mode set to normal and audio monitor out.)
• Panel Size: 0.74" diagonal (16:9 aspect ratio)
• Display Method: Transparent LCD panel (x 3, R/G/B)
• Pixels: 1,024,000 (1,280 x 800) x 3, total of 3,072,000 pixels
• Center-to-corner uniformity: 80%
• RGB: G: 0.7 Vp-p (1.0 Vp-p for sync on G), 75 ohms;
  B, R: 0.7 Vp-p, 75 ohms;
  HD/VD, SYNC: high impedance, TTL (positive/negative)
  NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.
• Keystone correction range: Vertical: ±30°
• Installation: Front/rear, ceiling/desk (menu selection)
• Power cord length: 6 ft., 7 in. (2 m)
• Dimensions including lens: 16-15/16" W x 4-15/16" H x 12-23/32" D (430 x 125.5 x 323 mm)
• Weight: Approximately 13.2 lbs (6 kg)
• Operating temperature*: 0°-40°C (32°-104°F)
  *The operating temperature range is 0°C (32°F) to 40°C (104°F) when used in High-Altitude mode (1,400 m [4,593 feet] to 2,700 m [8,858 feet]).  Also, if the ambient temperature exceeds 40°C (104°F) (35°C [95°F] in High-Altitude mode) when using all four lamps, the light output may be reduced approximately 30% to protect the projector.
• Operating humidity: 20%-80% (no condensation)
• Supplied accessories: Power cord with security lock (x1)
  Wireless remote control unit (x1)
  Batteries for remote control (AA/R6/LR6 type x 2)
  Software CD-ROM (Logo Transfer Software,Multi Projector Monitoring and Control Software V2.5, Wireless Manager ME 5.5) (x1)
• Throw Ratio: 1.34-2.68:1
• Colors: Full color (16,777,216 colors)
• Built-in speakers: 1-9/16" (4 cm), round (x1)
• LAN: RJ-45 for network connection, 10Base-T/100Base-TX, compliant with PJLink TM
• S-VIDEO In: Mini DIN 4-pin x 1, Y: 1.0 Vp-p, C: 0.286 V [p-p], 75 ohms
• VIDEO In: RCA pin x 1, 1.0 Vp-p, 75 ohms
• SERIAL IN: D-sub 9-pin (female) x 1 (for external control, RS-232C compliant)
• YPBPR (YCBCR): 480i (525i): fH 15.75 kHz; fV 60 Hz, 576i (625i): fH 15.63 kHz; fV 50 Hz, 480p (525p): fH 31.50 kHz; fV 60 Hz, 576p (625p): fH 31.25 kHz; fV 50 Hz, 720 (750)/60p: fH 45.00 kHz; fV 60 Hz, 720 (750)/50p: fH 37.50 kHz; fV 50 Hz,
• YPBPR (YCBCR) continued: 1080 (1125)/60i: fH 33.75 kHz; fV 60 Hz, 1080 (1125)/50i: fH 28.13 kHz; fV 50 Hz, 1080 (1125)/24p: fH 27.00 kHz; fV 24 Hz, 1080 (1125)/60p: fH 67.50 kHz; fV 60 Hz, 1080 (1125)/50p: fH 56.25 kHz; fV 50 Hz
• Terminals HDMI IN: HDMI 19-pin x 1, Deep Color, HDCP compatible
  480p (525p), 576p (625p), 720 (750)/60p, 720 (750)/50p, 1080 (1125)/60i, 1080 (1125)/50i, 1080 (1125)/24p, 1080 (1125)/60p, 1080 (1125)/50p
• Terminals HDMI IN continued: VGA (640 x 480)-WSXGA+ (1,680 x 1,050), compatible with noninterlaced signals only, dot clock: 25.2 MHz-146.25 MHz
  Audio signal: linear PCM (sampling frequencies: 48 kHz, 44.1 kHz, 32 kHz)
• Pixel configuration: Stripe
• HDMI/DVI/D: fH: 27.0 kHz-68.7 kHz, fV: 24 .0 Hz-85.0 Hz, dot clock: 25.2 MHz-148.5 MHz
• WIRELESS MODULE: Connector for optional wireless module ET-WM200U/WM200E x 1
• Lamp: 250 W UHM lamp
• Brightness**: 3,500 lumens
  **Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
• Resolution: 1,280 x 800 pixels (Input signals that exceed this resolution will be converted to 1,280 x 800 pixels.
• Contrast: 600:1 (full on/full off)
• DVI-I (analog)/RGB: fH: 15 .6 kHz-91.1 kHz, fV: 24 .0 Hz-85.1 Hz, dot clock: 162 MHz or lower
• Video/S-Video: fH: 15.75 kHz, fV: 60 Hz [NTSC/NTSC4.43/PAL-M/PAL60]
  fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM]
• Output power: 5.0 W (monaural)
• DVI-I IN: DVI-I 29-pin x 1
• Digital: DVI 1.0 compliant, compatible with HDCP, compatible with single link only
  480p (525p), 576p (625p), 720 (750)/60p, 720 (750)/50p, 1080 (1125)/60i, 1080 (1125)/50i, 1080 (1125)/24p, 1080 (1125)/60p, 1080 (1125)/50p
• Digital continued: VGA (640 x 480) -WSXGA+ (1,680 x 1,050), compatible with noninterlaced signals only, dot clock: 25.2 MHz-146.25 MHz
• Y, PB (CB), PR (CR): Y: 1.0 Vp-p (including sync signal); PB (CB), PR (CR): 0.7 Vp-p, 75 ohms
• COMPUTER (RGB) IN: D-sub HD 15-pin (female) x 1
• AUDIO IN 1: M3 x 1 (L, R x 1), input impedance: 22 kilohms or more
• AUDIO IN 2: M3 x 1 (L, R x 1), 0.5 Vrms, input impedance: 22 kilohms or more
• AUDIO IN 3: RCA x 2 (L, R x 1), 0.5 Vrms, input impedance: 22 kilohms or more
• AUDIO OUT: M3 x 1 (L, R x 1) (monitor out: 0-2.0 Vrms, variable)
• Cabinet materials: Molded plastic (PC + ABS)
• Operation noise: 33 dB (lamp mode: NORMAL), 29 dB (lamp mode: ECO)
• Remote Control Unit Power Supply: 3 V DC (R6/LR6/AA type battery × 2)
• Remote Control Unit Operation Range: Approximately 15 m (49 ft 3 in) when operated from directly in front of the signal receptor
• Remote Control Unit Dimensions: 1-13/32" W x 6-5/8" H  x 31/32" D (48 x 163 x 24.5 mm)
• Remote Control Unit Weight: Approx. 117 g (4.1 oz) (including batteries)
• Wireless Manager ME 5.5 system requirements: To use network functions, a PC is required that meets the conditions given below.
• OS: Microsoft® Windows® XP: Professional 32-bit, Home Edition 32-bit, Tablet PC Edition 2005 32-bit
  Windows Vista®: Ultimate 32-bit/64-bit, Business 32-bit/64-bit, Home Premium 32-bit/64-bit, Home Basic 32-bit/64-bit
• OS continued: Windows® 7: Ultimate 32-bit/64-bit, Professional 32-bit/64-bit, Home Premium 32-bit/64-bit
  Apple Mac OS X: v10.4, v10.5, v10.6
  Web browser:  Windows®: Internet Explorer 6.0/7.0/8.0
  Mac OS: Safari 2.0/3.0/4.0
• CPU: Windows®: 1 GHz or higher Intel® Pentium® III or higher, or other compatible processor
  Mac OS X: 1 GHz or higher PowerPC G4, or 1.8 GHz or higher Intel® Core TM processor
• Memory: 256 MB or more (512 MB or higher is recommended for Mac OS X)
• Free hard disk space  60 MB or more
• CD-ROM drive: CD-ROM drive or DVD drive (required for installation)
• Wireless LAN: The optional ET-WM200 is required.  IEEE 802.11b/g/n compatible (built-in wireless LAN system or external IEEE 802.11b/g/n LAN card must be installed and running normally.)
• Wireless LAN continued: Wireless connection may not be possible with some IEEE 802.11b/g/n wireless LAN systems. Macintosh computers must have a built-in wireless LAN adapter.
• Wireless LAN continued: For IEEE 802.11n connection, use a wireless LAN adapter, projector and access point that are IEEE 802.11n compatible, and connect with Infrastructure mode.
• Wired LAN connector: RJ-45
• Optional accessories: ET-LAF100A
• Replacement lamp unit: ET-EMF100
• Replacement filter unit: ET-PKF110H (for high ceilings)
• Ceiling mount bracket: ET-PKF110S (for low ceilings)
• Wireless module: ET-WM200U (for North America)