Aviom AV-P2 2-Channel Line Level Output Module for Pro16 A-Net

OUR PART #: AV-P2 MFR #: AV-P2

Copied to clipboard

The AV-P2 Output Module provides up to two channels of analog outputs from a Pro16 A-Net digital audio stream. ...Read more

Aviom AV-P2 2-Channel Line Level Output Module For Pro16 A-Net Image 1
Aviom AV-P2 2-Channel Line Level Output Module For Pro16 A-Net Image 2
Aviom AV-P2 2-Channel Line Level Output Module For Pro16 A-Net
No longer available at Full Compass
We've left this page up for reference only.

Questions? Contact our
Sales and Service Pros for expert
advice and package pricing.

800-356-5844

Email customer service

Product Overview

The AV-P2 Output Module provides up to two channels of analog outputs from a Pro16 A-Net digital audio stream. The analog output level for each channel is set with front-panel DIP switches.

AV-P2 modules can be connected in any combination of serial or parallel connections, using Pro16 A-Net Distributors. There is no limit to the number of devices that can be daisy chained, or to the number of parallel splits in a single system.

Each AV-P2 receives a 16-channel A-Net stream originating at a Pro16 input module, console interface card, or Pro64 audio network (via the ASI A-Net Systems Interface module).

A front-panel rotary switch allows the output to be set to any one of those 16 channels. If the selected channel is part of a stereo pair (set at the input module), the left and right channels are automatically routed to the left and right outputs on the AV-P2. If the selected channel is not part of a stereo pair, the channel's audio is routed to both the left and right outputs.

Audio is distributed to the AV-P2 over standard Cat-5e cables, using Aviom's A-Net digital audio protocol. A-Net supoprts plug-and-play installation, real-time distribution with sub-millisecond latency, and long cable runs up to 500 ft/150 m. Power can be supplied to the AV-P2 with an external DC power supply or over the Cat-5e cable (with an A-Net Distributor). Additionally, Pro16 A-Net audio streams can be transmitted over single- or multi-mode fiber optics using certain standard third-party media converters.

The AV-P2 has reversible mounting flanges. Two AV-P2 modules can be mounted side by side on a standard 1U rack tray. The AV-P2 is compatible with all Pro16 Series products.

Features

  • Provides 1- or 2-channel analog output from a Pro16 A-Net stream
  • Independently selectable output levels for left and right channels
  • 48kHz, 24-bit D/A converters
  • Optional power over Cat-5e using a Pro16 A-Net Distributor
  • Simple plug-and-play installation
  • Secure set-and-forget channel configuration
  • Reversible mounting flanges

Specifications

  • Audio Outputs
    • 2, impedance balanced line-level
    • 5.0 mm Euroblock connectors, female, panel-mount
    • 2 male Euroblock connectors supplied inbox
    • Screw terminals: Audio+; Audio-; Ground
  • Channel Selection: 16-position rotary switch
  • D/A Conversion: 48kHz, 24-bit
  • Output Levels
    • Variable: +4dBu to -31dBu in 1.5dB increments
    • 6-position DIP switch, per channel
  • Indicators: LEDs; red: Power, green: A-Net Active, yellow: Stereo Pair
  • Output Impedance: 100 ohms
  • Signal to Noise (unweighted): 93dB typical, A/D to D/A
    • Measured from AN-16/i Input Module to AV-P2
  • Freq. Response: 4Hz-22kHz +0.2dB/-3dB
  • THD+N: -93dB at -10dBFS
  • Crosstalk: -85dB at 1kHz
  • Bit Error Rate (BER): 10-12
  • Digital Connections: A-Net In: 1; A-Net Out: 1; RJ45 connectors
  • Pro16 A-Net: Uses unshielded Cat-5e UTP (or better) cable
  • Latency: < 0.880 msec (measured from analog input to analog output)
  • Power Supply: External, DC, universal switching type
    • Input Voltage:100-240 volts, 50/60Hz, 30VA
    • Output Voltage: 18-24 VDC, 0.5 amp
    • Plug Size: 2mm, locking, center pin hot
  • Dimensions: 7.45" wide x 7" deep; 1U high
  • Weight: 3.4 lbs

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.