Lectrosonics IFBT4-VHF Frequency Agile Compact IFB VHF Transmitter

The Lectrosonics IFBT4-VHF transmitter was designed for use in broadcast, motion picture, theater, and stage applications where extended operating range and high quality audio are essential. The transmitter can be used as a stand-alone device or patched directly into popular intercom systems.

The design is based upon the patented Lectrosonics Digital Hybrid Wireless® system.* While at the time of the first release of the product, there is only a companion analog receiver, the Digital Hybrid Wireless system is included for compatibility with future products.

Microprocessor control provides user-friendly operation and eliminates transients at turn-on and turn-off. The transmitter output is muted in the TUNE mode to avoid generating interference in other wireless systems while scrolling up and down to change frequencies. In the XMIT mode, the output is turned on and the frequency cannot be changed.

A supersonic pilot tone signal controls the audio squelch on the IFBR1A-VHF receiver to eliminate noise when the transmitter is turned off and it prevents the receiver from locking onto false signals. The pilot tone also eliminates noise in the receiver at turn-on and turn-off.

The LCD display is backlit for use in dimly lit conditions and is also highly visible in direct sunlight.

DIP switch settings on the rear panel provide direct compatibility with RTS and Clear Com intercom systems. A preamp stage is also included in the input stage to allow direct connection to dynamic microphones in “standalone” applications. Direct output at studio line level can also be fed directly into the transmitter.

The transmitter housing is rugged, machined aluminum with an electrostatic powder coating and an anodized finish. The unit is powered by 6 to 18 Volts DC via a locking connector. The supplied whip antenna is a detachable, 1/4 wavelength, flexible, galvanized steel cable that connects to a locking 50Ω BNC connector on the rear panel.

Features:

• Digital Hybrid Wireless® technology*
• Microprocessor controlled operation
• 50mW power output for long range use
• Pilot tone squelch control
• Multi-use XLR input jack
• Built-in microphone preamp
• DIP switch programmable intercom input
• Tx mute for frequency scrolling
• Multi-function LCD display
• Rugged machined aluminum construction

Specifications:

• Operating Frequencies (MHz): 174.100 to 215.750MHz
• Available Frequencies: 239
• Channel Spacing: 175kHz
• RF Power Output: 50mW
• Frequency Stability: +/- 001% (10ppm) @ 25°C
• Temperature Stability: +/- 001% (10ppm) from -30°C to +50°C
• Channel Selection: Momentary push-button switches, tune Up and Down
• Compatibility Modes (2): IFB and Digital Hybrid Wireless® (400 Series)
• Pilot Tone: 29.997 kHz IFB & 400 MODE; each frequency has a unique pilot tone
• Modulation:
  • IFB Mode: FM, +/- 20kHz deviation
  • Digital Hybrid Mode: +/- 75kHz
• Audio Frequency Response:
  • IFB Mode: 100Hz to 8kHz, +/- 1dB
  • Digital Hybrid Mode: 30Hz to 20kHz +/-1dB response (see Rolloff)
• Rolloff: Low frequency audio rolloff is menu selectable for 3dB down at 35Hz or 50Hz.
• Audio Compressor: 2 to 1 (IFB mode)
• Output Impedance: 50Ω
• Audio Input Levels:
  • 0dBu for Line, RTS1 and RTS2
  • -10dBu for Clear Com
  • -42dBu for mic dry inputs (no phantom power)
  • +/-50Vdc max
• Audio Input Config: Balanced and Unbalanced, rear panel selectable for Li
• Audio Input Impedance: Greater than 2K balanced, greater than 1K unbalanced at any gain setting
• Gain Control Range: -18dB to +24dB (0dB nominal center), Menu selectable
• Audio Input Jack: Standard XLR female connector
• Input Power: 12 to 14VDC typical, 200ma. max.; Max. Input Range 6 to 18VDC
• Power Input Jack: Coax type, locking LZR RL26AE
• Indicators: Backlit Liquid Crystal Display. Displays modulation meter, frequencies, modes, roll-off and audio level
• Front panel controls:
  • MENU momentary push-button switch
  • Power OFF-TUNE-XMIT, 3 position slide switch
  • Select Up momentary push-button switch
  • Select down momentary push-button switch
• Rear panel controls: Input Mode Select, 4 section DIP switch
• Weight: 9ozs
• Size: 5.25” L (including connectors) x 3.25” W x 1.25” H
• Emission designator: 180KF3E