(0)

Questions? Call Us:
800-356-5844

FSR, Inc TPRO-RXDS
TwisterPro™ UTP VGA Receiver

OUR PART #:  TPRO-RXDS

The TwisterPro™ UTP Transmitter / Receiver System allows video, stereo audio, RS-232 data and IR signal transmission over ordinary low cost CAT-5, 5e, 6 and cable.
Learn More
Our Price: $390.39
List Price: $429.00
You save 9%!
Write the first review.

Full Compass offers free ground shipping on thousands of stock and non-stock (special order) items for orders placed on this web site and shipping in the continental US (48 states).

Learn More

Free Shipping

Available

FSR, Inc TPRO-RXDS
Qty:
Usually ships in 7-14 business days.
Need it sooner? Call us!

Similar Products

The TwisterPro™ UTP Transmitter / Receiver System allows video, stereo audio, RS-232 data and IR signal transmission over ordinary low cost CAT-5, 5e, 6 and cable. This system offers the highest level of signal integrity. These high quality devices ensure reliable, error free transmission that is immune to interference from electrical noise. Cable runs of up to 1000 feet are within the capabilities of the system (see specs for maximum cable length details).

There are wall plate style transmitters (1-gang and 2-gang) and receivers (2-gang) offered in three colors; black, white, and ivory. Matching Decora™ trim rings are included for stand alone use, or the units be populated along with FSR’s IPS component and plates for a complete interface solution. There are also “brick” style housing versions that can be used on any surface or rack mounted using the accessory rack kits if preferred. (See TwisterPro™ accessories and ordering info).

TPRO receivers with skew compensation adjustments are optional and help adjust for misconvergence of the red, green and blue video signals that can occur as a result of inherent delay caused by differences in cable twist lengths.

The system can be powered at either the transmitter or receiver end by the optional power supply(s). If a TPRO- HUB is used, the hub with it’s included power supply, will power the other components in the system. This 1 in 8 out hub allows full expandability for demanding applications. Multiple hubs can be cascaded to achieve a maximum of 512 outputs.

Applications:

  • Boardrooms
  • Houses of Worship
  • Control Rooms
  • Classrooms
  • Digital Signage
  • Hotel/Conference Facilities
  • Temporary Staging and Rental

FSR, Inc TPRO-RXDS TisterPro™ Receiver Features:

  • Units can be powered at either end or throughoptional hub
  • Over-current sensing with LED indication
  • Video, RS-232 and IR LED indicators
  • Optional 1 in 8 out TPRO-HUB with power supply available

FSR, Inc TPRO-RXDS TisterPro™ Receiver Specifications:

  • RGB Video Input:
    • Connector: 1-HD-15 female connector
    • Signal Type: 1 RGBHV, RGBS, RGsB, RsGsBs,Component,S-video or Composite
    • Maximum Resolution: 1920 X 1080 (1080P)
    • Impedance: 75O
    • Level (nominal): Analog 0.7V p-p
    • Level (maximum): +-1.0 V
  • RGB Video Output:
    • Connector: 1-HD-15 female connector (Brick modelshave an additional HD-15 loopback connector)
    • Signal Type: Same as input
    • Gain: Unity
    • Impedance: 75O
    • Sync output: 5V into Hi Z, 2.2V into 75O
  • Audio Input:
    • Connector: 1-3.5 mm stereo mini jack (wallplates), 3pin Phoenix plug (bricks)
    • Signal type: Stereo unbalanced
    • Level (nominal): 0.25V RMS -10dBm
    • Level (maximum): 1.1V RMS, +3dBm
    • Impedance: 50 kO
    • Encoding: Full stereo 24 bit, 96kHz sample rate
    • Frequency response: 20Hz-15kHz +-0.5dB
  • Audio Outputs:
    • Connector:
      • Wallplate model receivers 2 RCA jack connectors
      • Brick model receivers 3 pin pluggable screw terminal
    • Signal type: Stereo unbalance
    • Impedance: 50O (Intended to drive a 600O or greaterload)
    • Gain: Unity +- 1.5dB
  • Control Adjustments:
    • Delay: Adjust Independent for R, G and B delay (Skewmodels only)
    • Delay range: 0-62 ns (Skew models only)
    • Video Boost Switch: Dip switch (OFF 0-800’/ON200-1000’)
    • Gain control: Manual combined control for RGB
  • RS-232 Data Input:
    • Number/Type: One DB-9 female connector. (4 pinPhoenix plug on brick models) DCE type connection for direct connection to aPC serial port included on two gang transmitters only. Must order TPRO-SerialDB-9 accessory harness for one gang transmitters.
    • Handshaking: Local loopback only (Models with DB-9connectors only)
    • RS-232 type: Unidirectional (data transmission from transmitter toreceiver only)
  • RS-232 Data Output:
    • Number/Type: One DB-9 male connector. DTE typeconnection for direct connection to peripheral.
    • Data Rate: 0-19.2k baud
  • Infrared Input:
    • Number/Type:
      • Both models have internal sensor logically OR’d with hardwired input.
      • T-PRO TX brick models One 4 pinpluggable Phoenix connector
      • T-PRO-TX wallplatemodels One C-grid SL 5-pin connector on the back of the unit.
    • Compatibility: Compatible with most IR outputs designed to drive an IRemitter LED.
  • Infrared Output:
    • Number/Type:
      • One 3.5 mm mini jack, center positive. All TPRO-RX models (Use FSR IR-EC1-6single or IR-EC2-6 dual emitter accessory.)
    • Output Switch: Dip switch (Normal 12 mW/High 60mW)
    • Carrier Range: 40 kHz, custom frequencies available per request.
  • Power Requirements:
    • TPRO-RX Receivers: 24VDC @ 0.12A (Skew models are24VDC @ 0.19A)
    • TPRO-TX Transmitters: 24VDC @ 0.09A
    • Power supplies are optional. Use FSR PS-24DC-500MA
  • Mechanical:
    • Model Dimensions (inches):
      • Transmitter enclosure
        • Brick 4.22 X 1.59 X4.10
        • Wall plate 1.70 X 4.09 X1.46
      • Receiver enclosure
        • Brick 4.22 X 1.59 X 4.10
        • Wall plate 3.56 X 4.09 X 1.2
  • General:
    • UTP cable wiring standard/ type EIA / TIA-568B CAT5,5E, 6
    • Recommended Transmission Range: 0-1000 ft with a single power supply (Upto 600’ when powered at transmitter. Up to 1000’ when powered at receiver.When using a TPRO-HUB with included power supply: The maximum distance to atransmitter is 1000’. The maximum distance to a receiver is 600’A distance ofup to 1000’ can be achieved by adding an additional power supply at the receiver.

To be the first to review this item, click here.

Add to Cart

We're sorry, only of this item available



Call a Sales Pro at 800-356-5844 for more information

© 2017 Full Compass Systems, LTD  9770 Silicon Prairie Parkway, Madison, WI 53593  All rights reserved.

We are not responsible for typographical errors in pricing or product specification
inaccuracies in our catalog or web site. Prices are subject to change without notice.