(0)

Questions? Call Us:
866-334-8859

Rosco Laboratories FLAMEX-WD
One Gallon of Flamex Flame Retardant for Wood

OUR PART #  FLAMEX-WD

Our Price: $65.83
List Price: $67.00
(Low Price Guarantee)
Usually ships in 7-14 business days.
Need it sooner? Call us!

Use Flamex WD to treat wood and cellulosic materials.  Plywood, board stock, sheet goods, hay, acoustical tile and other common materials can all be rendered flame retardant with Flamex WD.  After the Flamex treatment has dried fully, wood materials can be painted or stained without affecting the flame retardance.

Rosco Flamex WD has been premixed and does not require any further dilution.  The method of application and the amount of Flamex required for sufficient treatment varies with the materials in use.

One gallon of Flamex WD will treat approximately 150-200 square feet (14-18.5 square meters) of material.

Applying Flamex:

  • Dipping: This is the most efficient method ofimpregnation. Immerse completely for ten minutes, and hang to dry.
  • Brushing: Using a wide lay-in brush, brush the Flamexsolution into the fibers of the material being treated. Brush in the solutionusing a criss-crossing pattern to insure adequate absorption. Saturate thematerial, allow to absorb and then reapply a second treatment.
  • Spraying: In a spray application, it is very important that an adequate amount of the Flamex be absorbed. In calculating the amount of solution needed, remember that a substantial portion of the spray will not fall on the material. Use a Hudson-type sprayer with a medium nozzle setting. Saturate the material, allow to absorb and then reapply a second treatment.

The absorption rate of the wood or cellulosic materials being used may dramatically affect proper flame retardance.  Make sure you test for effective flame retardance.

Flamex WD has been approved for use by the California and New York City Fire Marshall and has been tested according to ASTM E84 Class B.

Store Flamex products in non-metallic containers.  When metal sprayers are used, they should be thoroughly cleaned immediately after use, including nozzles and accessories.  Avoid use of metal buckets or paint containers when possible.

DISCLAIMER: Read carefully the instructions supplied with any Flamex product.  Rosco offers these products in good faith, but without guarantee of any type, since materials treated and methods of application are beyond the control of the manufacturer.  You should determine suitability of the Flamex product for the intended use and always test before using.

Rosco Laboratories FLAMEX-WD
One Gallon of Flamex Flame Retardant for Wood

OUR PART #  FLAMEX-WD

Product Information:

Use Flamex WD to treat wood and cellulosic materials.  Plywood, board stock, sheet goods, hay, acoustical tile and other common materials can all be rendered flame retardant with Flamex WD.  After the Flamex treatment has dried fully, wood materials can be painted or stained without affecting the flame retardance.

Rosco Flamex WD has been premixed and does not require any further dilution.  The method of application and the amount of Flamex required for sufficient treatment varies with the materials in use.

One gallon of Flamex WD will treat approximately 150-200 square feet (14-18.5 square meters) of material.

Applying Flamex:

  • Dipping: This is the most efficient method ofimpregnation. Immerse completely for ten minutes, and hang to dry.
  • Brushing: Using a wide lay-in brush, brush the Flamexsolution into the fibers of the material being treated. Brush in the solutionusing a criss-crossing pattern to insure adequate absorption. Saturate thematerial, allow to absorb and then reapply a second treatment.
  • Spraying: In a spray application, it is very important that an adequate amount of the Flamex be absorbed. In calculating the amount of solution needed, remember that a substantial portion of the spray will not fall on the material. Use a Hudson-type sprayer with a medium nozzle setting. Saturate the material, allow to absorb and then reapply a second treatment.

The absorption rate of the wood or cellulosic materials being used may dramatically affect proper flame retardance.  Make sure you test for effective flame retardance.

Flamex WD has been approved for use by the California and New York City Fire Marshall and has been tested according to ASTM E84 Class B.

Store Flamex products in non-metallic containers.  When metal sprayers are used, they should be thoroughly cleaned immediately after use, including nozzles and accessories.  Avoid use of metal buckets or paint containers when possible.

DISCLAIMER: Read carefully the instructions supplied with any Flamex product.  Rosco offers these products in good faith, but without guarantee of any type, since materials treated and methods of application are beyond the control of the manufacturer.  You should determine suitability of the Flamex product for the intended use and always test before using.

Add to Cart

We're sorry, only of this item available



Call a Sales Pro at 800-356-5844 for more information

© 2016 Full Compass Systems, LTD  9770 Silicon Prairie Parkway, Madison, WI 53593  All rights reserved.

We are not responsible for typographical errors in pricing or product specification
inaccuracies in our catalog or web site. Prices are subject to change without notice.