Biamp D10SUB 10" Ceiling Subwoofer 200W

OUR PART #: D10SUB

Copied to clipboard

The Community D10SUB ceiling mount subwoofer provides powerful, high-impact bass response intended to augment any combination of Distributed Design Series full-range models. ...Read more

Biamp D10SUB 10" Ceiling Subwoofer 200W Image 1
Biamp D10SUB 10" Ceiling Subwoofer 200W
No longer available at Full Compass
We've left this page up for reference only.

Questions? Contact our
Sales and Service Pros for expert
advice and package pricing.

800-356-5844

Email customer service

Accessories

Product Overview

The Community D10SUB ceiling mount subwoofer provides powerful, high-impact bass response intended to augment any combination of Distributed Design Series full-range models. By including a complement of D10SUB’s into a distributed system, musical results that equal or exceed that of much larger and more costly surface-mount systems can readily be achieved. The D10SUB’s clean, clear bass response provides a compelling attraction for shoppers in a retail environment, and a memorable experience for bar, pub and restaurant patrons.

Dependent on program content and the size of the full-range Distributed Design models, the ratio of D10SUB’s to full-range models may vary from as few as 1:6 to as many as 1:1. For example, one D10SUB will provide strong supporting bass response for six D4’s or D5’s, while four D10SUB’s will better complement six of the more powerful D8’s or D10’s.

Like all Distributed Design models, the D10SUB installs quickly and easily. Exclusive Drop-Stop™ and Twist-Assist™ Tabs allow single-handed placement to speed the installation process. Drop-Stop’s spring-loaded legs support the back can on the included tile rails and snap-on C-ring, so that the installer no longer needs to hold the can against the tile while tightening the clamps. Twist-Assist performs a similar function for the baffle assembly: when the loudspeaker back cans are pre-installed into a conduit system for termination at a later date, a simple twist of the baffle into the back can brings the Twist-Assist clips together, supporting the baffle assembly while the installer fastens the screws.

The front-face wattage selector switch enables quick adjustment of levels, while the high-power internal autoformer permits full power output with 70V or 100V lines. A variety of installation accessories are available to accommodate different ceiling materials. The D10SUB face-only assembly and D10 back can are also available for separate purchase.

Community D10SUB Features:

  • Powerful, high-impact bass response
  • Internal passive low-pass crossover
  • Spring loaded Drop-Stop™ installation assistant tabs support the back can on the included rails and C-ring to simplify installation
  • Uniquely designed tile bridge support rails and snap-on C-ring support plates prevent sag
  • Twist-Assist™ loudspeaker face retainer tabs for fast and easy installation
  • 3/4" and 1" knock-outs on the sides of the back can
  • External loop-through Euroblock connectors
  • Rear cover with integrated cable clamp (strain relief) and optional conduit knockout
  • Selectable 8 ohm or 70V/100V operation
  • Back can and face-only packages available
  • Five year warranty

Community D10SUB Specifications:

  • Loudspeaker Type: Ceiling mount subwoofer
  • Operating Range: 42 Hz - 200 Hz
  • Frequency Response: 60 Hz - 160 Hz (+/- 5 dB)
  • Max Input Ratings (8 Ohm): 200W continuous, 500W program; 40 volts RMS, 89 volts momentary peak
  • Transformer Taps:
    • 70V: 200W, 100W, 50W, 25W and low impedance
    • 100V: 200W, 100W, 50W
  • Sensitivity (1W/1m): 93 dB SPL (63 Hz to 250 Hz 1/3 octave bands)
  • Maximum Output: 116 dB SPL / 122 dB SPL (peak 8 Ohm)
  • Nominal Impedance: 8 Ohms
  • Minimum Impedance: 8.4 Ohms @ 100 Hz
  • Nominal Coverage: 180º conical
  • Axial Q / DI: 1.7 / 2.3, 50 Hz to 200 Hz
  • Recommended Signal Processing: 41 Hz high pass filter
  • Drivers: LF 1x 10"
  • Driver Protection: Self-resetting solid state circuit breaker
  • Input Connection: 4-position Euroblock connector
  • Controls: Front-face wattage / low impedance selector switch
  • Enclosure: Corrosion-resistant zinc plated steel
  • Mounting/Rigging Provisions: 4 steel mounting clamps with 3-inch grip range
  • Grille: Powder coated steel with safety line, white finish, paintable
  • Baffle: Reflex loaded UL 94V-0 rated ABS
  • Safety Features: 4x safety hang points
  • Safety Agency Ratings: ETL listed to comply with UL1480, UL2043 and CSA60065. Suitable for use in air handling spaces per NFPA 70 and NFPA 90.
  • Face-Only / Back Can Options: D10SUB-FO Face-Only Assembly; D10-BC Back Can
  • Required Accessories: Electronic high pass filter
  • Supplied Accessories: C-Ring supporting plate, tile support bridge rails, grille, paint mask, cut-out template, flat screwdriver
  • Optional Accessories: D10-NCB New Construction Bracket
  • Dimensions:
    • Width: 15.197" (386 mm) bezel diameter
    • Depth: 9.938" (252.4 mm) can depth
    • Cutout Diameter: 14.125" (359 mm)
  • Weight: 24.8 lbs (11.2 kg)

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Product Documents

Click to download