(0)

Questions? Call Us:
800-356-5844

Radio Design Labs EZ-MXA20
20 Watt Stereo Mixer Amp with Tone Controls

OUR PART #  EZ-MXA20

Our Price: $214.02
List Price: $286.28
You save 25%! (Low Price Guarantee)
Usually ships in 7-14 business days.
Need it sooner? Call us!

Recommended Accessories

The EZ-MXA20 is a stereo mixer amplifier with one mic and two line inputs. Bass and treble tone controls are included. An integral compressor/limiter allows a higher sound output level without clipping than a standard amplifier. The outputs drive 4 or 8 ohm speakers.

The EZ-MXA20 is used in houses of worship, restaurants, clubs, meeting rooms and commercial sound systems. Power supply included.

Radio Design Labs EZ-MXA20 Features:

  • Audio Amplifier with Mic and Line Input Mixer
  • 10 Watts RMS Per Channel into 8 O
  • 8 Watts RMS Per Channel into 4 O
  • Switch-Selectable Load Impedance on Rear Panel
  • Balanced Microphone Input on XLR
  • Unbalanced Line Inputs on RCA Jacks
  • Switch-Selectable Phantom on Mic Input
  • Bass and Treble Tone Control Equalization
  • Integral Overload Limiter with LED Indicator
  • Limiter Controls Overloads from Clipping

Radio Design Labs EZ-MXA20 Specifications:

  • Inputs (3): 1.2 kO balanced on XLR jack, mic-level, -55 dBu Min. (for 10 Wout), -11 dBu max.(1); > 10 kO, -10 dBV nominal on RCA jacks, -13 dBV Min.(for 10 W out), +22 dBV max. (2)
  • Gain: Off to 74 dB (mic), Off to 32 dB (line)
  • Outputs (2): Left and Right, 10 Watts RMS into 8 O per channel or 8 Watts RMS into 4 O per channel, switch-selectable output impedance
  • Equalization: ±10 dB @ 10 kHz, ±9 dB @ 80 Hz
  • Frequency Response: 50 Hz to 20 kHz (±1.5 dB, mic input, 10 Watts), 35 Hz to 20 kHz (±1.5 dB, line input, 10 Watts)
  • THD+N: < 0.25%
  • CMRR: > -55 dB (mic)
  • Crosstalk: < -68 dB (1 kHz, line input)
  • Phantom: Switch-selectable 24 V (IEC 1938: 1996-12)
  • Noise: < -70 dB (below 10 Watts, -10 dBV line input), < -65 dB (below 10 Watts, -50 dBu mic input)
  • 24 Vdc power supply current: 170 mA (idle), 1000 mA (max.) Power supply included.
  • Power supply input voltage: 100 to 240 VAC
  • Warranty: 3 Years; contact RDL technical support department for assistance
  • Case dimensions: 5.75” (14.6 cm)W x 5” (12.7 cm)D
  • Mounting size: 1/3 rack width
24V @ 1000mA Power Supply
Radio Design Labs PS24KS 24V @ 1000mA Power Supply
Typical Performance: Input: 100 to 240 VAC Output: 24 Vdc, 1 A (UL, CSA) Dimensions: 1.80" x 3.51" x 1.55" (4.6  x 8.9 x 3.9 cm) Efficiency: ENERGY STAR Level IV
30.25 40.47 25
In Stock
Surface Mount Bezel 1/3 Rack
Radio Design Labs EZ-SMB2 Surface Mount Bezel 1/3 Rack
Surface mount bezel for 1/3 rack width EZ products.
28.95 34.17 15
In Stock
Under Counter Bracket
Radio Design Labs EZ-UCB2 Under Counter Bracket
Under counter bracket pair for all EZ product widths
18.97 22.40 15
In Stock
Component Chasis, 6 x 1/6 RU
Radio Design Labs EZ-CC6 Component Chasis, 6 x 1/6 RU
Component Chassis for 6 Increments of 1/6 Rack WidthFeatures: Mounts All EZ A/V Products Mounts EZ Storage Drawers Cover Lifts Off for Easy Product Mounting Integral Heavy-Duty Non-Skid Rubber Feet
82.25 110.03 25
Usually ships in 7-14 business days.
Need it sooner? Call us!
Rack Adapter
Radio Design Labs EZ-RA6 Rack Adapter
Rack Adapter for 6 Increments of 1/6 Rack Width Mounts All EZ A/V Products Mounts EZ Storage Drawers Base Plate Slides Out for Easy Product Mounting Occupies One RU in Standard 19¨ Rack
46.72 62.50 25
Usually ships in 7-14 business days.
Need it sooner? Call us!
Desktop Chassis 1/3 Rack
Radio Design Labs EZ-DC2 Desktop Chassis 1/3 Rack
Desktop Chassis for 1/3 Rack Width EZ Products Mounts 1/3 Width EZ Product to Desktop Installs Quickly With Two Screws Covers Cable Port in Desktop Provides Space for Excess Wire
45.25 60.52 25
Usually ships in 7-14 business days.
Need it sooner? Call us!
1/3 Rack Width Storage Drawer for EZ-RA6 or EZ-CC6
Radio Design Labs EZ-SD2 1/3 Rack Width Storage Drawer for EZ-RA6 or EZ-CC6
Features: Use In Place of Filler Panel(s) Holds Adapters and Cables Mount in EZ-CC6 or EZ-RA6
28.48 38.09 25
Usually ships in 7-14 business days.
Need it sooner? Call us!
1/6 Rack Width Storage Drawer for EZ-RA6 or EZ-CC6
Radio Design Labs EZ-SD1 1/6 Rack Width Storage Drawer for EZ-RA6 or EZ-CC6
RDL's EZ-SD1 is a 1/6 rack width storage drawer designed to mount in RDL's EZ-CC6 or EZ-RA6 rack adapters. The drawer holds adapters and cables and can be used in place of filler panels.
27.30 36.52 25
Usually ships in 7-14 business days.
Need it sooner? Call us!
Filler Panel, 1/6RU
Radio Design Labs EZ-FP1 Filler Panel, 1/6RU
Filler Panel - 1/6 Rack Width for EZ-RA6 or EZ-CC6.
9.50 11.20 15
Usually ships in 7-14 business days.
Need it sooner? Call us!

Click to download

Radio Design Labs EZ-MXA20
20 Watt Stereo Mixer Amp with Tone Controls

OUR PART #  EZ-MXA20

Product Information:

The EZ-MXA20 is a stereo mixer amplifier with one mic and two line inputs. Bass and treble tone controls are included. An integral compressor/limiter allows a higher sound output level without clipping than a standard amplifier. The outputs drive 4 or 8 ohm speakers.

The EZ-MXA20 is used in houses of worship, restaurants, clubs, meeting rooms and commercial sound systems. Power supply included.

Radio Design Labs EZ-MXA20 Features:

  • Audio Amplifier with Mic and Line Input Mixer
  • 10 Watts RMS Per Channel into 8 O
  • 8 Watts RMS Per Channel into 4 O
  • Switch-Selectable Load Impedance on Rear Panel
  • Balanced Microphone Input on XLR
  • Unbalanced Line Inputs on RCA Jacks
  • Switch-Selectable Phantom on Mic Input
  • Bass and Treble Tone Control Equalization
  • Integral Overload Limiter with LED Indicator
  • Limiter Controls Overloads from Clipping

Radio Design Labs EZ-MXA20 Specifications:

  • Inputs (3): 1.2 kO balanced on XLR jack, mic-level, -55 dBu Min. (for 10 Wout), -11 dBu max.(1); > 10 kO, -10 dBV nominal on RCA jacks, -13 dBV Min.(for 10 W out), +22 dBV max. (2)
  • Gain: Off to 74 dB (mic), Off to 32 dB (line)
  • Outputs (2): Left and Right, 10 Watts RMS into 8 O per channel or 8 Watts RMS into 4 O per channel, switch-selectable output impedance
  • Equalization: ±10 dB @ 10 kHz, ±9 dB @ 80 Hz
  • Frequency Response: 50 Hz to 20 kHz (±1.5 dB, mic input, 10 Watts), 35 Hz to 20 kHz (±1.5 dB, line input, 10 Watts)
  • THD+N: < 0.25%
  • CMRR: > -55 dB (mic)
  • Crosstalk: < -68 dB (1 kHz, line input)
  • Phantom: Switch-selectable 24 V (IEC 1938: 1996-12)
  • Noise: < -70 dB (below 10 Watts, -10 dBV line input), < -65 dB (below 10 Watts, -50 dBu mic input)
  • 24 Vdc power supply current: 170 mA (idle), 1000 mA (max.) Power supply included.
  • Power supply input voltage: 100 to 240 VAC
  • Warranty: 3 Years; contact RDL technical support department for assistance
  • Case dimensions: 5.75” (14.6 cm)W x 5” (12.7 cm)D
  • Mounting size: 1/3 rack width
24V @ 1000mA Power Supply
Radio Design Labs PS24KS 24V @ 1000mA Power Supply
Typical Performance: Input: 100 to 240 VAC Output: 24 Vdc, 1 A (UL, CSA) Dimensions: 1.80" x 3.51" x 1.55" (4.6  x 8.9 x 3.9 cm) Efficiency: ENERGY STAR Level IV
30.25 40.47 25
In Stock
Surface Mount Bezel 1/3 Rack
Radio Design Labs EZ-SMB2 Surface Mount Bezel 1/3 Rack
Surface mount bezel for 1/3 rack width EZ products.
28.95 34.17 15
In Stock
Under Counter Bracket
Radio Design Labs EZ-UCB2 Under Counter Bracket
Under counter bracket pair for all EZ product widths
18.97 22.40 15
In Stock
Component Chasis, 6 x 1/6 RU
Radio Design Labs EZ-CC6 Component Chasis, 6 x 1/6 RU
Component Chassis for 6 Increments of 1/6 Rack WidthFeatures: Mounts All EZ A/V Products Mounts EZ Storage Drawers Cover Lifts Off for Easy Product Mounting Integral Heavy-Duty Non-Skid Rubber Feet
82.25 110.03 25
Usually ships in 7-14 business days.
Need it sooner? Call us!
Rack Adapter
Radio Design Labs EZ-RA6 Rack Adapter
Rack Adapter for 6 Increments of 1/6 Rack Width Mounts All EZ A/V Products Mounts EZ Storage Drawers Base Plate Slides Out for Easy Product Mounting Occupies One RU in Standard 19¨ Rack
46.72 62.50 25
Usually ships in 7-14 business days.
Need it sooner? Call us!
Desktop Chassis 1/3 Rack
Radio Design Labs EZ-DC2 Desktop Chassis 1/3 Rack
Desktop Chassis for 1/3 Rack Width EZ Products Mounts 1/3 Width EZ Product to Desktop Installs Quickly With Two Screws Covers Cable Port in Desktop Provides Space for Excess Wire
45.25 60.52 25
Usually ships in 7-14 business days.
Need it sooner? Call us!
1/3 Rack Width Storage Drawer for EZ-RA6 or EZ-CC6
Radio Design Labs EZ-SD2 1/3 Rack Width Storage Drawer for EZ-RA6 or EZ-CC6
Features: Use In Place of Filler Panel(s) Holds Adapters and Cables Mount in EZ-CC6 or EZ-RA6
28.48 38.09 25
Usually ships in 7-14 business days.
Need it sooner? Call us!
1/6 Rack Width Storage Drawer for EZ-RA6 or EZ-CC6
Radio Design Labs EZ-SD1 1/6 Rack Width Storage Drawer for EZ-RA6 or EZ-CC6
RDL's EZ-SD1 is a 1/6 rack width storage drawer designed to mount in RDL's EZ-CC6 or EZ-RA6 rack adapters. The drawer holds adapters and cables and can be used in place of filler panels.
27.30 36.52 25
Usually ships in 7-14 business days.
Need it sooner? Call us!
Filler Panel, 1/6RU
Radio Design Labs EZ-FP1 Filler Panel, 1/6RU
Filler Panel - 1/6 Rack Width for EZ-RA6 or EZ-CC6.
9.50 11.20 15
Usually ships in 7-14 business days.
Need it sooner? Call us!

Click to download

Add to Cart

We're sorry, only of this item available



Call a Sales Pro at 800-356-5844 for more information

© 2017 Full Compass Systems, LTD  9770 Silicon Prairie Parkway, Madison, WI 53593  All rights reserved.

We are not responsible for typographical errors in pricing or product specification
inaccuracies in our catalog or web site. Prices are subject to change without notice.