Accessories for connectors, Panels, Plates

Red, round pushbutton switch. Front mount in .469 inch (11.91 mm) diameter hole in panels up to .297 inch (7.54 mm) thick. Solder terminals are standard. Mounting hardware is supplied. Completely enclosed in rugged metal housing. 1-C ...

Mystery Electronics' ModuLine inserts are fully interchangeable within their FMCA series and AW series products.

The RATPAC (Right Angle T connector PACkage) is a versatile kit for building a right angle connector for use with the SR receiver or Lectrosonics transmitters. The 3-pin configuration is normally used for the rear panel audio outputs of ...

Bag of 50 replacement crimp contacts for the NC3MXX-HA cable connector and the NC3MD-LX-HA receptacle

The Tilt 'N Plug Jr. with Circular Bezel model TNP131 is one member of compact interconnect solutions designed for installation into a table presentation system. The TNP131 provides access to computer video, audio, network, telephone, and ...

The TM1278 products are multimedia input plates designed for mounting against a surface, usually under a table or inside a podium. The front of the TM1278 offers the following pass-through connectors: One 15-pin HD female (with 12 in/30 ...

Micropunch Overview:The multiple mounting hole sets of the Micropunch units permit easy mounting on standard hole centers and included tie wraps can be used to dress incoming writes. All punchdown panels with Whirlwind QB-2 spring-loaded ...

Micropunch Overview:The multiple mounting hole sets of the Micropunch units permit easy mounting on standard hole centers and included tie wraps can be used to dress incoming writes. All punchdown panels with Whirlwind QB-2 spring-loaded ...

Connector plate for use with FP6 Series Floor Boxes.

1 RU, EH Panel Only.The EH Series by Switchcraft® is a complete line of audio, video, and data connectors built into standard panel-mount XLR housings. Custom combinations of EH Series connectors can be quickly loaded into any of our ...

Female HD15 to screw terminal. Terminals accept 18-30 gauge wire. 1.375"D x 0.75"H x 1.375"W (Female).

1-Gang stainless steel wall plate with 2 Pomona dual banana jacks (2-Black/2-Red).Features: Super High Quality Consistent Quick Delivery Punched Connectorized ProfessionalSpecifications: Dimensions: 4.500" x 2.75" Mounting screws ...

Used to hide unsightly cabling running between one connector plate and another connector plate.

Complete the look of your patch cables with this snagless boot cover which will protect the plug clip when cables are pulled through bundles. Easy to install, this cover will fit RJ-45 plugs for any Cat5, Cat5E, Cat6, or Cat6a patch cable. ...

Repack/Box OpenLowell’s RPS Series switch assemblies provide a low cost/low voltage method of remotely activating equipment that is connected to a remote power control such as Lowell RPC Series or a wide variety of sequence ...

The PNP402 is a package of parts that covers the basic needs of many Pop ’ N Plug users. When this item is ordered, it ships as a completely assembled product made up of: one PNP400 and two SP3500SC Sectional Plates with input labels ...

Lowell’s RPS Series switch assemblies provide a low cost/low voltage method of remotely activating equipment that is connected to a remote power control such as Lowell RPC Series or a wide variety of sequence controllers.  This ...

Used to hide unsightly cabling running between one connector plate and another connector plate.

Repack/Box OpenAll Tilt' N Plug Jr products belong to a family of compact interconnection solutions designed for installation into a table as part of a presentation system. They are designed for mounting into a table, podium, or other ...

Neutrik's HA-3MXX-SINGLE is a male crimp contact for the NC3MXX-HA cable connector and the NC3MD-LX-HA receptacle.